LAZER spots from Prospeed-UK

[Crofty]

Just ordered these bad boys with wiring harness and spot mounts.

Ben was great to deal with [emoji106]

Now the wait...

122538

[LRD414]

Wiring harness allow for piggy back connection to factory or just comes with a plug and tail?

Scott

[Crofty]

Wiring harness allow for piggy back connection to factory or just comes with a plug and tail?

Scott

Three methods Scott.

1. 8225-12V-SP wiring kit (8225-12V-SP), which enables you to wire the lamps just in the engine bay, without the need to pass wires through the bulkhead. It means that the lights will always switch on when you turn your vehicle high beams on.

2. If you want a separate switch in the dash, then you can buy the 8225-12V-SW harness kit (8225-12V-SW).

3. If your Discovery has Bi-Xenon headlights, and you want the lamps to activate directly with the main beams (i.e. without a separate switch), then you would need to buy the CanM8 module: CANM8 Cannect Highbeam - Electrical & Wiring - Products (https://www.lazerlamps.com/home/wiring-kits/canm8-highbeam).

Cheers,
Andrew

[Crofty]

Three methods Scott.

1. 8225-12V-SP wiring kit (8225-12V-SP), which enables you to wire the lamps just in the engine bay, without the need to pass wires through the bulkhead. It means that the lights will always switch on when you turn your vehicle high beams on.

2. If you want a separate switch in the dash, then you can buy the 8225-12V-SW harness kit (8225-12V-SW).

3. If your Discovery has Bi-Xenon headlights, and you want the lamps to activate directly with the main beams (i.e. without a separate switch), then you would need to buy the CanM8 module: CANM8 Cannect Highbeam - Electrical & Wiring - Products (https://www.lazerlamps.com/home/wiring-kits/canm8-highbeam).

Cheers,
Andrew

I'll chuck some pictures up once they are fitted.
May be a while until that happens, my baby has just gone in for $18k's worth of hail damage [emoji22]

[Tombie]

Only method 2 is legal in AU

[Crofty]

Only method 2 is legal in AU

Yep made sure I got the right one [emoji16]

[Crofty]

Finally got round to fitting the LAZER spots so a couple photo's for you all to see. Very impressed with the fitment and the power of these lights!
https://www.aulro.com/afvb/images/imported/2017/07/244.jpg
https://www.aulro.com/afvb/images/imported/2017/07/245.jpg
https://www.aulro.com/afvb/images/imported/2017/07/246.jpg
https://www.aulro.com/afvb/images/imported/2017/07/247.jpg
https://www.aulro.com/afvb/images/imported/2017/07/248.jpg

[Strop]

Crofts, any chance of a picture of the mounts please?

Thanks

Laurie

[Crofty]

Crofts, any chance of a picture of the mounts please?

Thanks

Laurie

Hi mate,

Unfortunately I never took any photos whilst adding the mounts.
Here are a few more photos showing the mounts and the different configurations of spots available.

Cheers,
Andrew

https://www.aulro.com/afvb/images/imported/2017/07/229.jpg
https://www.aulro.com/afvb/images/imported/2017/07/230.jpg
https://www.aulro.com/afvb/images/imported/2017/07/231.jpg
https://www.aulro.com/afvb/images/imported/2017/07/232.jpg

[DieselLSE]

Only method 2 is legal in AU
Yes, but Option 3 (CANM8) caters for that: "There are 2 connections to the vehicle CAN Bus wiring (CAN Hi & CAN Lo) along with a connection to a switched 12v power supply and an earth connection."

[twr7cx]

The mounts are not too badly priced < Discovery 3&4 Front Spotlight Mounts : ProSpeed (http://prospeed-group.co.uk/product/discovery-34-front-spotlight-mounts/) > but the extra for the Lazer lights supplied is a lot.

[Mog60]

You can get Lazer Lamps from an Australian distributer. I don't know if it makes much difference but it might save on postage.