Results 1 to 8 of 8

Thread: Mil Water Jerricans

  1. 12th December 2009, 07:41 PM #1
    4bee's Avatar
    4bee
    4bee is offline Cynical Moi?
    Join Date
    Jan 1970
    Location
    Adelaide Hills. South Australia
    Posts
    13,349
    Total Downloaded
    0

    Mil Water Jerricans

    Military Water Jerricans
    I have a couple of the Mil Plastic Jerrys & the small cap fails, probably due to the small thread & the effort required to tighten it appears to "blow" the centre out of the cap at it's weakest point of the moulding.

    I have replaced with the same but they also fail, so is there a better cap available for these. It is only the small one that fails.

    Thank you
    Reply With Quote Reply With Quote
  2. 13th December 2009, 12:16 PM #2
    inside's Avatar
    inside
    inside is offline Wizard Subscriber
    Join Date
    Jan 1970
    Location
    Melbourne
    Posts
    1,545
    Total Downloaded
    0
    Do you have arms of steel? Sure you're not doing it too tight? No problem with my military water jerries but maybe they are of a different design? Mine are these type.

    Reply With Quote Reply With Quote
  3. 13th December 2009, 12:37 PM #3
    4bee's Avatar
    4bee
    4bee is offline Cynical Moi?
    Join Date
    Jan 1970
    Location
    Adelaide Hills. South Australia
    Posts
    13,349
    Total Downloaded
    0
    Wouldn't have thought so being aware of the problem.

    Mine are the genuine OZ Mil cans with 2 bungs on top only, no tap. I realise it seals on an O ring so doesn't need balls of steel.

    Actually your one looks a better design. If that tap was a FM thread (which it doesn't look like) it could be a good replacement for the bung.
    Reply With Quote Reply With Quote
  4. 13th December 2009, 06:10 PM #4
    inside's Avatar
    inside
    inside is offline Wizard Subscriber
    Join Date
    Jan 1970
    Location
    Melbourne
    Posts
    1,545
    Total Downloaded
    0
    You can get the ones pictured for about $20 from army disposals stores if that works out easier than modifying yours.
    Reply With Quote Reply With Quote
  5. 13th December 2009, 08:50 PM #5
    4bee's Avatar
    4bee
    4bee is offline Cynical Moi?
    Join Date
    Jan 1970
    Location
    Adelaide Hills. South Australia
    Posts
    13,349
    Total Downloaded
    0
    Thanks. I think it will.
    Reply With Quote Reply With Quote
  6. 13th December 2009, 09:58 PM #6
    gazk's Avatar
    gazk
    gazk is offline Master
    Join Date
    Dec 2007
    Location
    Cambewarra, NSW
    Posts
    517
    Total Downloaded
    0
    Quote Originally Posted by 4bee View Post
    Wouldn't have thought so being aware of the problem.

    Mine are the genuine OZ Mil cans with 2 bungs on top only, no tap. I realise it seals on an O ring so doesn't need balls of steel.

    Actually your one looks a better design. If that tap was a FM thread (which it doesn't look like) it could be a good replacement for the bung.
    I had one of those pictured with the tap/bung at the bottom and replaced it with the genuine OZ Mil cans with the two screw caps on the top. Heavier plastic and champhered corners on the base - I think the genuine article will handle more abuse, I haven't had a problem with the screw caps/Orings.
    Regards
    Reply With Quote Reply With Quote
  7. 14th December 2009, 10:56 AM #7
    digger's Avatar
    digger
    digger is offline ForumSage Subscriber
    Join Date
    Sep 2007
    Location
    RIVERLAND, SOUTH AUSTRALIA
    Posts
    6,740
    Total Downloaded
    0
    http://www.aulro.com/afvb/remlr-gene...ighlight=jerry

    just for info-- 2 sizes, one for mil jerry holder (water) is 22litre



    digger
    (REMLR 235/MVCA 9) 80" -'49.(RUST), -'50 & '52. (53-parts) 88" -57 s1, -'63 -s2a -GS x 2-"Horrie"-112-769, "Vet"-112-429(-Vietnam-PRE 1ATF '65) ('66, s2a-as UN CIVPOL), Hans '73- s3 109" '56 s1 x2 77- s3 van (gone)& '12- 110
    Reply With Quote Reply With Quote
  8. 14th December 2009, 10:58 AM #8
    wovenrovings
    wovenrovings is offline Master Supporter
    Join Date
    Jun 2006
    Location
    Bundaberg Qld.
    Posts
    632
    Total Downloaded
    0
    What happens is the the plastic in the caps becomes brittle with age. Happened to mine. They were only 18 years old, you would think they would last longer,
    84' 120" ute - 3.9 isuzu.
    Reply With Quote Reply With Quote
« Finch 3 Way Controls | Hot water systems »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!