Results 1 to 10 of 10

Thread: Leakage

  1. 21st February 2015, 07:27 PM #1
    Paultan
    Paultan is offline Master Supporter
    Join Date
    Mar 2014
    Location
    New Zealand
    Posts
    109
    Total Downloaded
    0

    Leakage

    Whilst a leaking Land Rover isn't unusual, i noticed this evening some grease on the front drivers side wheel. Looks like it's come through the wheel hub?? I'll try to post some pic tomorrow, but any idea where the grease is coming from and mor importantly what do I need to do?

    Cheers
    Paul
    Reply With Quote Reply With Quote
  2. 22nd February 2015, 05:48 AM #2
    JDNSW's Avatar
    JDNSW
    JDNSW is offline RoverLord Silver Subscriber
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    29,511
    Total Downloaded
    0
    It will be either coming from behind the drive flange (leaking gasket - loose studs or just damaged gasket, but possible indicator of loose wheel bearing) or from under the plastic hub cap (replace or clean up and refit using a suitable sealant, depending on condition).

    It does not fit your description, but could also be from the oil seal on the inside of the hub - a somewhat bigger job to replace.

    John
    John

    JDNSW
    1986 110 County 3.9 diesel
    1970 2a 109 2.25 petrol
    Reply With Quote Reply With Quote
  3. 22nd February 2015, 07:33 AM #3
    Paultan
    Paultan is offline Master Supporter
    Join Date
    Mar 2014
    Location
    New Zealand
    Posts
    109
    Total Downloaded
    0
    Perfect. Thanks for that John, all fixed.
    Reply With Quote Reply With Quote
  4. 22nd February 2015, 11:22 AM #4
    JDNSW's Avatar
    JDNSW
    JDNSW is offline RoverLord Silver Subscriber
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    29,511
    Total Downloaded
    0
    Quote Originally Posted by Paultan View Post
    Perfect. Thanks for that John, all fixed.
    Which was it?

    John
    John

    JDNSW
    1986 110 County 3.9 diesel
    1970 2a 109 2.25 petrol
    Reply With Quote Reply With Quote
  5. 22nd February 2015, 02:28 PM #5
    Paultan
    Paultan is offline Master Supporter
    Join Date
    Mar 2014
    Location
    New Zealand
    Posts
    109
    Total Downloaded
    0
    Quote Originally Posted by JDNSW View Post
    Which was it?

    John
    Leaking gasket !
    Reply With Quote Reply With Quote
  6. 22nd February 2015, 04:13 PM #6
    BadCo.'s Avatar
    BadCo.
    BadCo. is offline Wizard
    Join Date
    Jun 2014
    Location
    Waitakere, New Zealand
    Posts
    1,270
    Total Downloaded
    0
    Quote Originally Posted by Paultan View Post
    Leaking gasket !
    Were the drive flange bolts lose? Or just an old gasket?
    Reply With Quote Reply With Quote
  7. 22nd February 2015, 05:28 PM #7
    John H
    John H is offline Fossicker Subscriber
    Join Date
    Aug 2013
    Location
    Kadina SA
    Posts
    80
    Total Downloaded
    0
    Check your breather line.It could be blocked,hence causing the problem(pressure build up).Similar issue with my rear wheels (still to be rectified).
    Reply With Quote Reply With Quote
  8. 22nd February 2015, 07:37 PM #8
    Paultan
    Paultan is offline Master Supporter
    Join Date
    Mar 2014
    Location
    New Zealand
    Posts
    109
    Total Downloaded
    0
    Quote Originally Posted by BadCo. View Post
    Were the drive flange bolts lose? Or just an old gasket?
    Bolts were lose as well.
    Reply With Quote Reply With Quote
  9. 22nd February 2015, 08:03 PM #9
    JDNSW's Avatar
    JDNSW
    JDNSW is offline RoverLord Silver Subscriber
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    29,511
    Total Downloaded
    0
    Quote Originally Posted by Paultan View Post
    Bolts were lose as well.
    Jack the wheel up and check for loose wheel bearings - loose bolts are sometimes a symptom of this (other times, poor workmanship!).

    John
    John

    JDNSW
    1986 110 County 3.9 diesel
    1970 2a 109 2.25 petrol
    Reply With Quote Reply With Quote
  10. 23rd February 2015, 02:41 AM #10
    BadCo.'s Avatar
    BadCo.
    BadCo. is offline Wizard
    Join Date
    Jun 2014
    Location
    Waitakere, New Zealand
    Posts
    1,270
    Total Downloaded
    0
    Quote Originally Posted by Paultan View Post
    Bolts were lose as well.
    There is a torque setting in the workshop manual somewhere.

    Edit: found it

    Hub driving member to hub 60-70nm
    Reply With Quote Reply With Quote
« flat dog or terrafirma flares on a perentie | Jerry Can Holders »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!