Results 1 to 7 of 7

Thread: Knocking

  1. 27th June 2011, 03:55 PM #1
    Waxenwane's Avatar
    Waxenwane
    Waxenwane is offline Master
    Join Date
    Mar 2007
    Location
    Seaford, Near Franganistan, Victoria
    Posts
    388
    Total Downloaded
    0

    Knocking

    Hmmn, I have ignored a vibration that has appeared in the last few days to my peril. I had thought the exhaust was rubbing but the noise has escalated to a very bad knocking so much so I thought i'd done a big end, but no the knock is coming from the trans area so I suspect a loose torque converter or something in that area. The knock is engine driven not there on coast.
    So I was hoping someone may have come across this before????
    Have it parked up now and will start undoing bolts tomorrow.
    Reply With Quote Reply With Quote
  2. 28th June 2011, 08:00 AM #2
    bigcarle's Avatar
    bigcarle
    bigcarle is offline Master Supporter
    Join Date
    Aug 2009
    Location
    lota, brisbane
    Posts
    604
    Total Downloaded
    0
    have you checked the universals on the tailshafts?
    Reply With Quote Reply With Quote
  3. 28th June 2011, 03:37 PM #3
    Tank's Avatar
    Tank
    Tank is offline AT REST
    Join Date
    Jan 1970
    Location
    Moruya Heads/Sth. Coast, NSW
    Posts
    6,532
    Total Downloaded
    0
    Quote Originally Posted by bigcarle View Post
    have you checked the universals on the tailshafts?
    X2, esp. the front uni at the transfer case end, Regards Frank.
    Reply With Quote Reply With Quote
  4. 28th June 2011, 06:57 PM #4
    Waxenwane's Avatar
    Waxenwane
    Waxenwane is offline Master
    Join Date
    Mar 2007
    Location
    Seaford, Near Franganistan, Victoria
    Posts
    388
    Total Downloaded
    0
    Noise occurs when stationary or moving so that rules out driveline
    Reply With Quote Reply With Quote
  5. 28th June 2011, 09:10 PM #5
    Bradtot's Avatar
    Bradtot
    Bradtot is offline Wizard Silver Subscriber
    Join Date
    Jan 1970
    Location
    Two Rocks WA
    Posts
    1,361
    Total Downloaded
    0
    Sounds like cracked Flex plate. Take off the inspection cover and get a screwdriver and try and move the flex plate. When I did this to mine it creaked and groaned and made horrible noises. I then got a torch and turned the motor over by the front pully and then could see the cracks around the bolts.
    Brad
    Range Rovers Have Charactors inside them
    LROCWA Ex member 23 years
    1971 Series 2A
    2004 Discovery2a V8 Auto
    2003 Discovery2a TD5 Manual
    1982 4door man (sadly now gone)
    1989 Vogue auto
    2011 TDV8 Vogue
    What would life be without a Rangie?


    Reply With Quote Reply With Quote
  6. 29th June 2011, 09:38 AM #6
    goldey's Avatar
    goldey
    goldey is online now Master Supporter
    Join Date
    Apr 2007
    Location
    Newcastle NSW
    Posts
    362
    Total Downloaded
    0
    I hate to say, but I agree with Bradtot. My Disco is a 98 tdi auto.

    I had a similar noise coming from the back of the motor, immediately thought it was the big ends stuffed, but on closer inspection by my LR mechanic, turns out it was a cracked flex plate. So much so that the only thing holding the flex plate to the central bolt pattern was a small piece of steel that hadn't cracked between two of the 6 bolts...... .

    Any more driving and fix would have been a bit more severe....

    Uni's are easy to rule out, slide under and give them a good shake, should feel no sideways movement. If there is even a smallish amount pull them out asap and put in new ones. They're relatively cheap, but if they let go down the freeway........ no need to explain the result......

    Cheers

    Goldey
    Just arrived: 2012 D4 3.0 HSE, the journey begins again ;-).
    Gone: 98 Disco 300tdi Auto, and some extras
    Reply With Quote Reply With Quote
  7. 30th June 2011, 06:06 AM #7
    bigcarle's Avatar
    bigcarle
    bigcarle is offline Master Supporter
    Join Date
    Aug 2009
    Location
    lota, brisbane
    Posts
    604
    Total Downloaded
    0
    Uni's are easy to rule out, slide under and give them a good shake, should feel no sideways movement. If there is even a smallish amount pull them out asap and put in new ones. They're relatively cheap, but if they let go down the freeway........ no need to explain the result......
    not always, as i tried this with my uni's and there was no movement sideways or any way, the only clue i had was first thing in the morning i took it for a small drive up the road to isolate the noise and when i came home i tried to shake the uni and get movement out of it and still had none. but the clue was all the other parts where cool to touch but the uni near the transfer box was pretty warm but the gearbox flange was not. took tail shaft off and bingo that uni was totally seized . i installed 2 new ones and fixed the problem
    Reply With Quote Reply With Quote
« Grinding noise when travelling | Disco 300TDi electrics all dead. »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!