Results 1 to 5 of 5

Thread: Master+Slave Cylinder & Front crank pulley replacement

  1. 9th December 2013, 01:38 PM #1
    PerthPT
    PerthPT is offline Fossicker
    Join Date
    Oct 2013
    Location
    Perth
    Posts
    17
    Total Downloaded
    0

    Master+Slave Cylinder & Front crank pulley replacement

    Gday all, so I've run into a few issues with my lovely new disco 1 300tdi - its basically **** itself haha.

    Since i cant really afford to get a mechanic to do it i'm planning on fixing her up as best i can myself.

    The fellas at Jordan rover tech recon my crankshaft pulley has come loose so it needs to be replaced,
    Does anyone know of a good step by step guide to replacing it? Or have any helpful hints? Will i need any additional seals or will a new puller just replace the old?

    Second problem is that apparently my master and slave cylinders are on their way out, the clutch isnt fully extending and sometime when i get into the car the clutch will be all the way in and i have to pull it out.
    Same question again, does anyone have a step by step guide to replacing the master and slave cylinders or have any recommendations or warnings?

    Im thinking of perhaps doing the master+slave myself and leaving the front crank pulley to the experts... Thoughts?

    Cheers for the help.
    Reply With Quote Reply With Quote
  2. 9th December 2013, 07:06 PM #2
    loanrangie's Avatar
    loanrangie
    loanrangie is offline LordRover Subscriber
    Join Date
    Jan 1970
    Location
    St Helena,Melbourne
    Posts
    16,777
    Total Downloaded
    1.13 MB
    The master cylinders are a pretty simple replacement and a manual or the RAVE disc will help for that task.
    What is the problem with the balancer , is it flogged out ?
    MY08 TDV6 SE D3- permagrin ooh yeah
    2004 Jayco Freedom tin tent
    1998 Triumph Daytona T595
    1974 VW Kombi bus
    1958 Holden FC special sedan
    Reply With Quote Reply With Quote
  3. 9th December 2013, 08:14 PM #3
    PerthPT
    PerthPT is offline Fossicker
    Join Date
    Oct 2013
    Location
    Perth
    Posts
    17
    Total Downloaded
    0
    The crankshaft balancer/damper/pulley (they're all the same thing right?) is wobbling around when the engine is on causing a lund rattling/clocking noise. Could it be anything else? I've actually grabbed the pulley and it feels solid when i try to wiggle it, but i can see it moving about when the engine is on.
    Reply With Quote Reply With Quote
  4. 9th December 2013, 09:04 PM #4
    PerthPT
    PerthPT is offline Fossicker
    Join Date
    Oct 2013
    Location
    Perth
    Posts
    17
    Total Downloaded
    0
    Could it be a problem with the crank shaft itself?
    Reply With Quote Reply With Quote
  5. 11th December 2013, 09:36 PM #5
    loanrangie's Avatar
    loanrangie
    loanrangie is offline LordRover Subscriber
    Join Date
    Jan 1970
    Location
    St Helena,Melbourne
    Posts
    16,777
    Total Downloaded
    1.13 MB
    It could be the loose balancer has now flogged out the keyway on the crank .
    MY08 TDV6 SE D3- permagrin ooh yeah
    2004 Jayco Freedom tin tent
    1998 Triumph Daytona T595
    1974 VW Kombi bus
    1958 Holden FC special sedan
    Reply With Quote Reply With Quote
« CDL | How much paint..??? »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!