Page 1 of 2 12 LastLast
Results 1 to 10 of 19

Thread: V8 taking longer to start

  1. #1
    Join Date
    Oct 2007
    Posts
    220
    Total Downloaded
    0

    V8 taking longer to start

    Recently my Disco has been cranking over for longer before firing up. Tonight it took about 5seconds - prompting my concern and this post.
    Im due to take it on a 800km trip tomorrow night I don't want any problem when Im in the middle of no where.

    Is this a pre-cursor for a problem known in discos?

    Any ideas on what could be causing it.

    Any quick replies will be appreciated.

    Cheers,
    Rez

  2. #2
    Join Date
    Jan 1970
    Location
    Adelaide - Torrens Park
    Posts
    7,291
    Total Downloaded
    0
    Could be a lazy fuel pump. Possibly old spark plugs. Leaking injectors causing overly rich mixture on startup.

  3. #3
    Join Date
    Oct 2007
    Posts
    220
    Total Downloaded
    0
    Sorry bit of background....pump was only replaced 2weeks ago. Plugs are 3000km old and injectors I couldnt tell you but had major service 3000km ago.

    Rez

  4. #4
    Join Date
    Jan 1970
    Location
    Gold Coast Queensland Australia
    Posts
    6,469
    Total Downloaded
    0
    which engine?
    normally the v8 starts within a few seconds.
    if you switch the key to the on position, without turning to start, you can hear the pump in the tank run and stop. it takes about 1 to 2 seconds, so that eliminates fuel supply problems.
    so my guess would be the ignition module, or coil.
    i also had a dodgy connector to the coil, the connector was broken in the insulation, but felt ok when pushing it on or taking it off.
    of course the voltage to the module and coil needs to be good, so if you have a starting battery that is low you can expect problems.
    if the pump noise is not there, try depressurising the fuel rail [3.9 engine] and then listen for the pump. [3,9 has a shraeder valve on the right side if the plenum in the fuel rail, push the valve like letting a tyre down, until all the pressure is gone then turn the key to on, you should hear the pump, if it works, go the ignition system]
    happy holiday
    Safe Travels
    harry

  5. #5
    Join Date
    Jan 1970
    Location
    Avoca Beach
    Posts
    14,152
    Total Downloaded
    0
    I think that sometimes a leaking fuel pressure regulator is to blame for this.
    I have just bought a new one form LRdirect which took forever to get here.

    I the meantime try to prime the rail twice before attempting start ie turn ign on, listen for click after 3 seconds, turn off then on and wait until click again , then start.
    My 92 RRC will then start almost first cylinder.

    I hope to change mine next week if I get time.
    Regards Philip A

  6. #6
    Join Date
    Oct 2007
    Posts
    220
    Total Downloaded
    0
    Its a 97 model 3.9lt

  7. #7
    Join Date
    Dec 2008
    Location
    Victoria
    Posts
    1,777
    Total Downloaded
    0
    A blocked or clogged fuel filter will cause this too.

  8. #8
    Join Date
    Jan 1970
    Location
    Gold Coast Queensland Australia
    Posts
    6,469
    Total Downloaded
    0
    Quote Originally Posted by Rezley View Post
    Its a 97 model 3.9lt
    so where are you rezley?
    i don't think a leakin fuel pressure regulator will be the problem,
    when i had problems, i contacted the major spares supplier for land rover, they had only sold two regs.

    my starting problems were never much of an issue, but the intermittent stopping was.
    finally tracked down to the plug on the top of the fuel pump being a poor connection, so maybe you are suffering the early stages of that,
    it's a long story as to how i eventually cornered the answer to the problem, but
    go to the pump connector, and look for any signs of heat or arcing, black brass terminals.
    to find the plug, first unload the luggage in the rear,
    under the carpet about in the center of the load space, there is a round panel, unscrew this and you will see the top of the tank and the plug for the pump and fuel gauge.
    just pop the connector off and look closely at the terminals, both in the connector and the white plastic pump housing, they should all be nice and bright, no black.
    two terminals work the fuel gauge and the other two run the pump.

    what time are you leaving in the morning?

    when i finally confirmed the fault, i was on a trip a long way from home, buying a soldering iron and solder tricked it into lasting until i got home.
    Safe Travels
    harry

  9. #9
    Join Date
    Oct 2007
    Posts
    220
    Total Downloaded
    0
    Thanks for all the ideas, I'll have to look at pump terminals if it gets worse. Not leaving till tomorrow night after work. Will also try priming pump instead of turning key straight away without waiting.

    Cheers,

    Rez

  10. #10
    Join Date
    Jan 2010
    Location
    NSW
    Posts
    151
    Total Downloaded
    0
    I have a simliar problem with my d1.
    Starts fine when cold.
    Mostly start fine when warm (normal temp)
    Occasionally doesnt start when warm, I have been thinking that it has been getting flooded, or flooded like symptons.
    I found that if I just let it wind over it will not start, the battery will start to show signs of flattening...understandable after winding it over for 30 sec or so.

    What I found has, if i start it with full throtle, it helps to lean it back to a usable mixture, and will usually start with about 8-10 sec.

    So think it may be leaking injector, but dont know how to check it. But my work around for now, gets me out of trouble, when it doesnt start.
    Rusty

Page 1 of 2 12 LastLast

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!