Results 1 to 7 of 7

Thread: Injector Loom etc.

  1. 25th July 2019, 10:28 AM #1
    Bohica's Avatar
    Bohica
    Bohica is online now YarnMaster Subscriber
    Join Date
    May 2015
    Location
    Williamstown, Victoria
    Posts
    3,247
    Total Downloaded
    0

    Injector Loom etc.

    I am changing the leaking rocker cover gasket and front and rear cam shaft bore seals. I thought I'd change the injector loom as well, as a preventtative measure. I removed the engine loom plug from the head and bugger me sideways it had oil on it!! What a suprise. I have a couple of questions.
    1/ How can I remove the oil from the engine loom?
    2/ I have seen a couple of video clips on replacing the loom. One used a rubber mallet to fit the injector loom into its hole, the other one said use lubrication, use engine oil? or a water based lube like KY?

    Thanks in advance

    Julian
    D2a Td5 Manual, Chawton White. aka "Daisy"
    Build date 11th Oct 2003
    Freelander 2 2011, manual, the daughter calls it Perri
    Before I had a Land Rover I did not have any torque wrenches. Now I have three.
    LROCV #1410
    Reply With Quote Reply With Quote
  2. 25th July 2019, 11:40 AM #2
    Charles
    Charles is offline Master
    Join Date
    Aug 2009
    Location
    Canberra
    Posts
    146
    Total Downloaded
    0
    Julian, FWIW I had no need to use force to refit injector look plug, pushed in with only moderate resistance. To clean oil out of engine loom I pulled loom out, stripped the tape, hung from rafter and used contact cleaner, brake cleaner and compressed air. Took multiple applications over several days before I got all the oil out. To be fair, I had a lot of oil in the loom, so this level of effort may not be necessary.
    Cheers, Charles
    Reply With Quote Reply With Quote
  3. 25th July 2019, 12:13 PM #3
    PhilipA
    PhilipA is offline Swaggie Subscriber
    Join Date
    Jan 1970
    Location
    Avoca Beach
    Posts
    14,152
    Total Downloaded
    0
    The problem is not so much oil getting into the injector loom as there are no seals on the injector plugs and oil will creep up the wires.
    The problem is that the seal on the plug lets oil through into the main loom and it migrates up to the ECU and then into it and causes shorts betwen pins.
    I pulled my plug and laboriously split each wire and used butt connectors to isolate the oil and filled the plug with silastic.
    However the loom that I bought about 5 years ago has never seemed to leak through the plug and I have my modified one hanging up in my garage never used.
    I think the later ones have good sealing on the plug, so buy a later one and hopefully have no problems.
    Regards Philip A
    BTW , whats this about a hammer? that is bizarre.
    Reply With Quote Reply With Quote
  4. 25th July 2019, 02:03 PM #4
    Bohica's Avatar
    Bohica
    Bohica is online now YarnMaster Subscriber
    Join Date
    May 2015
    Location
    Williamstown, Victoria
    Posts
    3,247
    Total Downloaded
    0
    Hammer time 12:00 minutes mark.
    YouTube

    As for the oil in the loom, this might be a while as the car is my daily drive. Time to check the RED plug.
    D2a Td5 Manual, Chawton White. aka "Daisy"
    Build date 11th Oct 2003
    Freelander 2 2011, manual, the daughter calls it Perri
    Before I had a Land Rover I did not have any torque wrenches. Now I have three.
    LROCV #1410
    Reply With Quote Reply With Quote
  5. 25th July 2019, 02:32 PM #5
    jwb's Avatar
    jwb
    jwb is offline Master Supporter
    Join Date
    Jan 1970
    Location
    Melbourne, AU
    Posts
    840
    Total Downloaded
    0
    Go back 10 years in the archives to search on this. The oil is in the wire core itself so washing the outside of the wires does nothing.

    Change the injector loom every so often and keep the red plug clean. Also take the sealing rubber out of the red plug so that the oil can leak out and not accumulate in the plug connectors.
    _________________________
    1996 D1 V8 - gone
    2002 D2 Td5 ES- gone but still running elsewhere
    2013 D4 SDV6 HSE - gone
    2023 Defender 110SE D300
    Reply With Quote Reply With Quote
  6. 25th July 2019, 03:14 PM #6
    PhilipA
    PhilipA is offline Swaggie Subscriber
    Join Date
    Jan 1970
    Location
    Avoca Beach
    Posts
    14,152
    Total Downloaded
    0
    I have seen everything now with the ****** hitting in the plug with a rubber mallet. (although I must admit to tapping injectors in with a light nylon mallet)

    The problem BTW is not the outside of the plug leaking, that would only drain down to your alternator.(ha ha)'

    That is actually the sole purpose of the front camshaft plug so no usurping here thankyou.

    The problem is that the old plugs were not sealed well inside where the male leads went into the female plugs.
    Regard sPhilip A
    Reply With Quote Reply With Quote
  7. 25th July 2019, 05:27 PM #7
    Kaaaiju
    Kaaaiju is online now Master Subscriber
    Join Date
    Jul 2017
    Location
    Victoria
    Posts
    834
    Total Downloaded
    0
    Where can you buy the female pins that go into the red ecu play?
    Reply With Quote Reply With Quote
« Starting Problems | Replacing wiper blades (not refills) »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!