Reply With QuoteUmmm, I'm thinking the elevator. What kind of system is it? Elector hydraulic? 3 phase? Star delta configuration? or just delta? Or single phase? electric motors can pull a lot of power at start up.
ForumSage
SubscriberI'd go with the inverters - 7 also. Big inrush currents on switchmode supplies until they stabilise.
Regards,
Tote
Go home, your igloo is on fire....
2014 Chile Red L494 RRS Autobiography Supercharged
MY2016 Aintree Green Defender 130 Cab Chassis
1957 Series 1 107 ute - In pieces
1974 F250 Highboy - Very rusty project
Assorted Falcons and Jeeps.....
Master
SubscriberUmmm, I'm thinking the elevator. What kind of system is it? Elector hydraulic? 3 phase? Star delta configuration? or just delta? Or single phase? electric motors can pull a lot of power at start up.
04 L322 Vogue V8 - Work truck
07 Freelander 2 TD4 SE - The wifes
74 Leyland P76 Targa Florio - Aspen Green
91 Kawasaki GPZ900R
Previous LRs = 78IIa series - 81, 93, 95 RRC - D2V8
OldBushie
6
Very Very Lucky!
Hydraulic. Sub 200 w turning on. Not much over 800 if going up. Not the culpritOriginally Posted by FisherX
Very Very Lucky!
Leds cut my power bill by >30% when all on sub 600w and not hit to start up - not this one
Wizard
SubscriberI know what it is. You put too many deer carcasses in your computerized axial tomography (CAT) scanner. Possibly put yourself in there as well!
2013 D4 expedition equipped
1966 Army workshop trailer
(previously SII 2.25 swb, SIII 2.25 swb & lwb, P38 Vogue, 1993 LSE 3.9V8 then HS2.8)
OldBushie
You may have 800 of them for all we know, helps to know your loads.Leds cut my power bill by >30% when all on sub 600w and not hit to start up - not this one
Very Very Lucky!
Fair point Vern
4 led tubes in most rooms About 60 of them and 64 led down lights . The answer and how we found it tomorrow. Leave it for a while in case some one nails it before thenThe power savings and significantly reduced replacment cost from the LEDs has been very welcome. Hardly on top of a ladder any more at all.
Very Very Lucky!
Royal Melbourne Hospital and MIA radiology have honestly zapped me with xrays , MRIs and CT scans far more than decent. No radiology at my place at all except for looking at the results and cool images
Very Very Lucky!
Lazer Printers are very quick and cheap to run. Tonner and drums are not cheap to buy yet last me a long time. On friday we had eliminated every other item and done that several times to ensure consistency.
The sparky and myself had seen with all computers and Printers being only item on almost no grid impacts and had mistakenly left them of the list of likely suspects until the very end.'
We stripped to the wires a power lead and had a nifty device showing the exact current flowing to the devices as we turned them on.
Each of the printers was very consistant. several seconds after power on they went in to a start up process which on just one case was almost as much a a kettle/Microwave/ Hot water/ Lift.... Times by 8 printers the results was far more than decent for the circuit breaker or Victron Inverters or the power supply from my two batteries for just the briefest of time
Printing is a requirement that is reducing fast with E Scripts and E Referrals. A small UPS to each of them is the interim solution. Holding them on for a few seconds means no shock loading of my whole building.
Surprised myself and not shocked no one guessed noting Vern did mention the devil is in the detail with how many things not jsut what they are. Well done Vern. Nailed the missing very important bit Sir.
| Search AULRO.com ONLY! |
Search All the Web! |
|---|
|
|
|
Bookmarks