Oh Dear! What am I going to do?

Printable View

Show 40 post(s) from this thread on one page

24th July 2007, 10:43 PM
p38arover

Quote:

Originally Posted by 4bee

Ah well, what can you do?:D

Zackly!

Well, she'll find out tomorrow when I drag it out of the garage to try to start it.

I don't know where the battery fits - that's the first job.

I crawled under it yesterday and it looks pretty sound. There is, unfortunately, no PTO. There is only a propshaft from about halfway back and out the rear of the rear crossmember.

I'm not quite sure where to start - front or back. Take off the tray and clean up all the back end and paint the rear half of the chasis (and fit my new shocks!) or strip the front end and do it.

The back might be quicker and I'll see something for my efforts.

Ron
24th July 2007, 11:23 PM
dobbo

What step is denial?
25th July 2007, 07:14 PM
p38arover

Today my wife noticed the Landie was gone from the neighbour's across the road.

I inadvertently left the LH garage door open this morning (the Landie is behind the RH door). She looked out and said "A Land Rover wouldn't fit in that garage with all your junk"

We'll see what happens tomorrow when I drag the Landie out to try to get the engine running.

Ron
25th July 2007, 07:55 PM
DiscoStew

This is better than reality TV!!
25th July 2007, 07:56 PM
DiscoTDI

ha ha ha ha ha, your screwed:p
25th July 2007, 08:01 PM
UncleHo

G'day P38arover :)

The battery on a 2a Landy will be in one of 2 places, on the right hand side between the steering box and the radiator on a battery tray that incorporates the Oil Bath Aircleaner, OR under the Pass seat, lift the seat pad and there will be alid with a front clip/lever, the cables will come through from the engine bay, Is ther a blank-off plate at the back of the G/box-transfer, if not when you have it running and engage gear it will empty the transfer on the backyard, the blank off plate is about 6" dia held on by 6 nuts, it also has a small roller bearing in the centre of the inner face, there is apaper gasket, but a Vita-Brits packet type will do;) gearbox/transfer oil is EP90, check clutch/brake fluid, (should be a tin dual brake/clutch reservoir) if early series 2/2a starter is press type under dash solenoid.

cheers
25th July 2007, 08:13 PM
p38arover

UncleHo, yes there is a blanking plate over the PTO location.

I had a look at the Expo on Sunday and saw trhge battery was in the location you described but it looks like it won;t fit there on mine.

I'll take soem under bonnet pics tomorrow.

Unfortunately I don't have a 2A manual, only a genuine SIII manual. I had a look in the Markets ion this forum but the 2A doesn't appear to be covered.

Hoever, I did see on eVilBay, this CD version from Tassie for $15: http://cgi.ebay.com.au/Landrover-Lan...QQcmdZViewItem
25th July 2007, 08:26 PM
easo

Quote:

Originally Posted by p38arover

Good to see another reader of Pournelle. His columns were the first thing I read in Byte.

Re my beast, this afternoon I asked Elisabeth if she'd like to have a look at the 2A. She declined saying "You don't really have it."

One can only do so much.... :D

Ron

The greatest trick the devel ever pulled was to make people belive he didn't exist. Or somthing like that.
25th July 2007, 08:41 PM
loanrangie

Ron, i hope that tray has enough room to roll a sleeping bag out on, it may be your bed for the next few months!
25th July 2007, 09:09 PM
p38arover

Quote:

Originally Posted by loanrangie

Ron, i hope that tray has enough room to roll a sleeping bag out on, it may be your bed for the next few months!

It does. I could almost fit my centre pole tent on the back!

Ron

Show 40 post(s) from this thread on one page