Results 1 to 10 of 10

Thread: UV affected plastic bits

  1. #1
    RichardK is offline ChatterBox Silver Subscriber
    Join Date
    Jan 1970
    Location
    Western Australia
    Posts
    2,955
    Total Downloaded
    0

    UV affected plastic bits

    Does anyone have any suggestions on how to restore UV affected grille and bumper ends, they are on my 94 RRC and I would like to bring them up to scratch
    RichardK

    Series IV Matrix Offroad Camper following our Discovery 3 with E Diff, BAS Remap, Mitch Hitch, Uniden UHF, Codan NGT HF, Masten TPMS, Proquip Compressor Guard, ARB Winch Bar, Milemarker Hydraulic Winch, 4x4 Intelligence Rear Wheel Carrier, VMS GPS with Rear Camera,

  2. #2
    Join Date
    Jan 1970
    Location
    Down the road from Sydney
    Posts
    14,702
    Total Downloaded
    0
    back to black is what I use but only blackens them up for a bit...then you have to reapply
    Our Land Rover does not leak oil! it just marks its territory.......




  3. #3
    Join Date
    Oct 2008
    Location
    Brisbane
    Posts
    1,243
    Total Downloaded
    0
    I used "armour all" on my defender flares and grill 6 mths ago and they are still black.

  4. #4
    RichardK is offline ChatterBox Silver Subscriber
    Join Date
    Jan 1970
    Location
    Western Australia
    Posts
    2,955
    Total Downloaded
    0
    Unfortunately these aren't grey, they have oxidized
    RichardK

    Series IV Matrix Offroad Camper following our Discovery 3 with E Diff, BAS Remap, Mitch Hitch, Uniden UHF, Codan NGT HF, Masten TPMS, Proquip Compressor Guard, ARB Winch Bar, Milemarker Hydraulic Winch, 4x4 Intelligence Rear Wheel Carrier, VMS GPS with Rear Camera,

  5. #5
    Join Date
    Jan 2007
    Posts
    1,251
    Total Downloaded
    0
    kitten tyre shine - absolutely great , makes them look like new

  6. #6
    Join Date
    Aug 2006
    Location
    WA
    Posts
    13,786
    Total Downloaded
    0
    I used this stuff on my 110 grille. Worked brilliantly. It is a dye, not a paint - so soaks in, rather than just coating on top.
    VHT Vinyl Dye

  7. #7
    Join Date
    Jan 1970
    Location
    SYDNEY -in the shire.....
    Posts
    8,196
    Total Downloaded
    0
    yep......use a hair dryer or a hot air gun........and slowly heat up the surface bit by bit........

    it will look new again.......but dont know for how long.......
    do not overheat to melt the plastic.......just enough till its shiny and new looking again......


  8. #8
    Join Date
    May 2009
    Location
    Tatura, Vic
    Posts
    6,336
    Total Downloaded
    0
    Haven't tried this my self but a bloke once told me to restore the faded plastic on my trail bike to warm it with a heat gun and melt bees wax onto it.

    Dave.

  9. #9
    Join Date
    Sep 2007
    Location
    Aussie Expat in NZ
    Posts
    3,451
    Total Downloaded
    0
    avoid anything with silicon in it. It will look great - at first - but will actually break down the plastic, making it brittle and dull and even worse.

    I use and recommend:

    Welcome to Meguiar's Australia, the Leader in Car Car products

    Meguiars Gold Class Trim Detailer. You can use it on your dash, guards, window rubber etc. Keeps it all good - its like sunscreen too. Actually helps stop the problem, not just the symptom.

    Armorall, black tire shine etc all use silicon.
    Hercules: 1986 110 Isuzu 3.9 (4BD1-T)
    Brutus: 1969 109 ExMil 2a FFT (loved and lost)

  10. #10
    Join Date
    Mar 2007
    Location
    Kalgoorlie WA
    Posts
    5,546
    Total Downloaded
    0
    Quote Originally Posted by flagg View Post
    avoid anything with silicon in it. It will look great - at first - but will actually break down the plastic, making it brittle and dull and even worse.

    I use and recommend:

    Welcome to Meguiar's Australia, the Leader in Car Car products

    Meguiars Gold Class Trim Detailer. You can use it on your dash, guards, window rubber etc. Keeps it all good - its like sunscreen too. Actually helps stop the problem, not just the symptom.

    Armorall, black tire shine etc all use silicon.
    x 2

    This is all I will use on mine. Even works well on the rubbers below the side windows.

    Auto Glym also have a similar product - haven't tried it yet, so can't really comment.

    Definitely agree with flagg's advice to steer clear of anything with silicon in it.

    A while back, I was using Turtle Wax "ICE" on the rubber and trim - seems to work well on rubber, but the plastic trim, while initially looking good, starts to go white at the edges after a while in the sun.

    This stuff is supposed to be a good "all purpose" wax / polish. In fact, while it seems to work well on rubber, it is crap on paintwork (bloody hard to buff off) and whatever you do, you don't want to get it on glass. I've thrown it out.
    Cheers .........

    BMKAL


Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!