Results 1 to 7 of 7

Thread: Which one is it

  1. 24th April 2012, 12:46 PM #1
    Ivan's Avatar
    Ivan
    Ivan is offline Master
    Join Date
    May 2007
    Location
    Scarborough QLD
    Posts
    524
    Total Downloaded
    0

    Which one is it

    I have an occasional fault on my D3. When I put the suspension into access height it starts to lower the car, then I get a message saying it's been put in extended mode and to reset the height once clear of the obstacle. My conclusion is that I have a faulty height sensor(s). So is there any way I can track it down to which one(s) is/are faulty?

    Thanks

    Ivan
    Reply With Quote Reply With Quote
  2. 24th April 2012, 01:28 PM #2
    Graeme
    Graeme is online now Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    If you have a Llams kit fitted you should remove its loom first and if the fault no longer occurs then look here http://www.aulro.com/afvb/1657476-post94.html about having the loom fixed. However a fault only when lowering to access height doesn't sound like a Llams connector problem.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  3. 24th April 2012, 02:24 PM #3
    Ivan's Avatar
    Ivan
    Ivan is offline Master
    Join Date
    May 2007
    Location
    Scarborough QLD
    Posts
    524
    Total Downloaded
    0
    Forgot to add, no Llams fitted but I do have Faultmate MSV2.

    Ivan
    Reply With Quote Reply With Quote
  4. 24th April 2012, 02:30 PM #4
    gghaggis's Avatar
    gghaggis
    gghaggis is offline ChatterBox
    Join Date
    Jan 1970
    Location
    Perth
    Posts
    2,248
    Total Downloaded
    0
    So what does the Faultmate say?

    Cheers,

    Gordon
    Reply With Quote Reply With Quote
  5. 24th April 2012, 08:06 PM #5
    CaverD3
    CaverD3 is offline ChatterBox
    Join Date
    Mar 2008
    Location
    Sydney, Australia
    Posts
    2,351
    Total Downloaded
    0
    The compressor dryer could be blocked, stops the vehicle exhausting the air and it thinks it is stuck.
    Remove dryer sieve and microwave the beads.
    Reply With Quote Reply With Quote
  6. 26th April 2012, 07:41 PM #6
    NavyDiver's Avatar
    NavyDiver
    NavyDiver is offline Very Very Lucky! Gold Subscriber
    Join Date
    Feb 2010
    Location
    Melbourne
    Posts
    10,247
    Total Downloaded
    0

    extended hieght

    Mine (2005 D3 Se) was doing the same when lowering to access height untill Ritters replaced a few bits. My rear end was lowering very slowly and I assume the sensor we can use to trick our cars into extended height (shove a log under the tow bar when lowering) was sending my car up high.
    This was noted before LLAMS was installed on mine. It was fixed but not at my request as I actually liked it.
    If yours starts going up high toggle the switch back to lower it and you will get down. Having access to exended mod.e might be very usefull at times. It is fixable but i wouldn't ask for it myself.
    Reply With Quote Reply With Quote
  7. 26th April 2012, 11:30 PM #7
    unseenone's Avatar
    unseenone
    unseenone is offline Master
    Join Date
    Apr 2011
    Location
    Austin, TX, US
    Posts
    149
    Total Downloaded
    0
    Put it on the 4x4 information screen if you have one and drive it around normally. Watch for one of the wheel height indicators acting strange. That should be your culprit.

    Consider putting together a spares kit for traveling remote areas, which should include such common failure items. There is a write up with pictures here; DISCO3.CO.UK - View topic - Upcoming project
    Reply With Quote Reply With Quote
« Wreckers or other source of used parts? | Rhino Bars »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!