Front Sensors / Front Camera

Quote:

---

Originally Posted by Lukeis

Thanks Dave, sounds very achievable.. How much is dirt cheap?

No rush but when you're free can you send me the part numbers? Just as I started to think I was nearing the end of my upgrades!!

---

I'll post the list here....
Sensors x 4 LR038084 (though the OEM 9G92-15K859-DA is readily available, as it's used in about 20 different vehicles, I paid $70 delivered for 4)
4 rubber grommets LR011193 or LR015497 depending if you want black or transparent.
2 centre retainers LR015238
2 LH/RH retainers LR015239

These items are the same for any year D4.

For the loom, if you have two connectors under the RH headlamp (one of which will be in use by the fog lamps loom), you can get away with adding loom LR015493 (or you may find it as LR021049).
This definitely is right for the pre update D4, for the post update D4, I haven't seen what the connectors under the headlamp look like yet, and there's about 16 variants of that front loom.
If someone wants to PM me a VIN for a MY14 or newer D4, I can try and work out which one is best.

i assume the button on the dash would need to be added also. How hard is it pull the dash apart on these things?

Quote:

---

Originally Posted by sheerluck

But you should know whether you're going forwards or backwards. ;)

---

Judging by the markings on SWMBO's Camry, I think she struggles with this concept sometimes. :wasntme:

Bigstu,

The center dash is not as hard as you may think, I've done it a few times messing around with the touch screen. as always a few clips get lost and nerves are stressed pulling hard on plastic parts, but all in all it's pretty easy, at least on my 2011..

In case anyone is looking to do this, I ordered the parts today at the following cost:

Sensors x 4 LR038084 = $50 delivered (eBay)
4 rubber grommets LR011193 = $28 (LR parts)
Wiring loom LR021049 - $58 (Lr parts)

I wasnt initially going to do this upgrade except I got a facelift bumper and it had the holes there so I figured why not!

wait for delivery, install the bumper then off to the shop to update the CCF.

Does anyone know what to look under for this setting?

Quote:

---

Originally Posted by sheerluck

I'll post the list here....

This definitely is right for the pre update D4, for the post update D4, I haven't seen what the connectors under the headlamp look like yet, and there's about 16 variants of that front loom.
If someone wants to PM me a VIN for a MY14 or newer D4, I can try and work out which one is best.

---

Thanks for this. PM on its way
David

Finally got the car. Its a 2016 16.5. I'm going to get an ARB summit bar fitted wondering if it would be best to buy the loom and parts and get ARB to fit them all at the same time?

Having installed these only a week ago you 100% will want to install them at the same Time as the bullbar. While mine was only going into a bumper so the room available might be different the bumper definitely had to be completely off to do the wiring etc

Ps. Now having had them for a week I would have to say they are pretty useless in real life, but as you said that's not an arguement worth having!

Good Luck!!

So I ordered all of the parts required, sent my vin number to Duckworth LR to make sure it would all be ok. When I pulled out my drivers side headlamp to find the loom, there is only one plug there even close to the same size as the sensor loom and the fog lamp is connected to it. The fog lamp is using only two wires as you would expect but there is no way the sensor loom would plug into that connector anyway. Have I been sent the wrong loom or is this going to be the nightmare I think it is??

If you are referring to the parking sensors loom keep looking, from memory there is an additional loom which sounds like the one you are referring too!

I think I had to take the headlight and grill out to find it.