Page 4 of 4 FirstFirst ... 234
Results 31 to 39 of 39

Thread: Trailer Stability Assist

  1. 24th February 2019, 02:51 PM #31
    DiscoJeffster
    DiscoJeffster is offline TopicToaster Subscriber
    Join Date
    Mar 2016
    Location
    Perth
    Posts
    4,335
    Total Downloaded
    0
    Quote Originally Posted by rocket rod View Post
    Do you have to put one on each indicator (I couldn't be bothered frankly)?
    Supposedly not though for completeness I did. When you indicate, the trailer light on the dash flashes and is another indicator the trailer is detected. With only one side, you won’t see the flash on the non-modified side. It doesn’t matter, it’s still detected, just whether you’re a pedant like me or not and want the indicator for both sides.
    2010 TDV6 3.0L Discovery 4 HSE
    2007 Audi RS4 (B7)
    Reply With Quote Reply With Quote
  2. 24th February 2019, 02:57 PM #32
    kelvo
    kelvo is offline Wizard Subscriber
    Join Date
    Dec 2009
    Location
    Baldivis WA
    Posts
    1,275
    Total Downloaded
    0
    Quote Originally Posted by wardy1 View Post
    Went over a weighbridge on the way home actually.
    Trailer was 2250kg (with gas bottles and 1 of 2 100ltr water tanks full). The car came in at 3320kg so gross was 5570kg. Well within the limits according to the handbook.
    Which water tank was full front or rear? If it was the rear that would most likely be the reason for the swaying, the heavy rear will act like a pendulum keeping the sway going.
    2014, MY14 Discovery TDV6, Fuji White (2018-Now)
    2003, Discovery 2a, Td5 Manual, Zambezi Silver (2012-2018)
    2007, Adventure Offroad Campers, Grand Tourer (2015-Now)
    Reply With Quote Reply With Quote
  3. 24th February 2019, 04:30 PM #33
    LRD414's Avatar
    LRD414
    LRD414 is offline Super Moderator Subscriber
    Join Date
    Oct 2014
    Location
    Brisbane
    Posts
    3,737
    Total Downloaded
    0
    Quote Originally Posted by wardy1 View Post
    ... The trailer assist DEFINITELY wasn’t working as we had very uncomfortable trailer sway on several occasions.
    Did the vehicle change behaviour to correct the sway or did you intervene? I’ve never felt it operate but understand it to be very subtle.

    Scott
    D4 TDV6 MY14 with Llams, Tuffant Wheels, Traxide DBS, APT sliders & protection plates, Prospeed Winch Mount w/ Carbon 12K, Mitch Hitch & Drifta Drawers
    Link to my D4 Build Thread
    D3 2005 V8 Petrol
    Ex '77 RRC 2 door. Long gone but not forgotten.
    Reply With Quote Reply With Quote
  4. 25th February 2019, 09:08 AM #34
    wardy1's Avatar
    wardy1
    wardy1 is offline ChatterBox Supporter
    Join Date
    Jan 1970
    Location
    Ringwood, Vic
    Posts
    2,127
    Total Downloaded
    0
    I had to either slow down or apply the electric brakes manually
    D4 SDV6, a blank canvas
    Reply With Quote Reply With Quote
  5. 25th February 2019, 10:19 AM #35
    cjc_td5's Avatar
    cjc_td5
    cjc_td5 is offline ChatterBox
    Join Date
    Aug 2007
    Location
    Bunbury, WA
    Posts
    2,507
    Total Downloaded
    0
    Quote Originally Posted by rocket rod View Post
    Do you have to put one on each indicator (I couldn't be bothered frankly)?
    No. Only one side is required.
    Reply With Quote Reply With Quote
  6. 25th February 2019, 10:32 AM #36
    Redback's Avatar
    Redback
    Redback is offline Swaggie Subscriber
    Join Date
    Jan 1970
    Location
    Ellendale Tasmania.
    Posts
    12,986
    Total Downloaded
    0
    Quote Originally Posted by rocket rod View Post
    Thanks for your responses on this issue. I'm now the proud owner of 2 Chinese metal load resistors ($15) that are yet to be installed. What I would like to know from someone is what method they used to install one in the car (instead of the trailer) so they can be used on any trailer eg hire units. My guess is there would need to be a switch to turn them on/off so TSA is not active full time?
    TSA is on all the time as it's mechanical, so can't be turned off or on, it works by sensing trailer sway.
    Cheers Baz.

    2011 Discovery 4 SE 2.7L
    1990 Perentie FFR EX Aust Army
    1967 Series IIa 109 (Farm Truck)
    2007 BMW R1200GS
    1979 BMW R80/7
    1983 BMW R100TIC Ex ACT Police
    1994 Yamaha XT225 Serow
    Reply With Quote Reply With Quote
  7. 12th April 2019, 07:13 PM #37
    rocket rod
    rocket rod is offline Master Subscriber
    Join Date
    Jun 2009
    Location
    Perth
    Posts
    576
    Total Downloaded
    1.13 MB
    Sorry to bring this old thread up again but I've installed the load resistor onto the RHS car indicator using a switch in the circuit. I've checked the wiring job with a test lamp and that flashes in unison with the indicators (and doesn't when I flick the switch) but I don't get any trailer icon on the dash. Do I have to have a trailer attached to make it happen or should the dash icon flash without a trailer?
    Rod

    D4 MY16 5 seat TDV6 - LLAMS, Custom Drawers, OL Bar, Toyo Open Country, GOE Rims, Lithium DBS, eDiff, OA Long Range Tank, GAP Tool, Tracklander rack, Mitch Hitch, TPMS & Safari Snorkel
    Reply With Quote Reply With Quote
  8. 12th April 2019, 08:15 PM #38
    disco4now's Avatar
    disco4now
    disco4now is offline Master Subscriber
    Join Date
    Jan 2010
    Location
    Sydney
    Posts
    151
    Total Downloaded
    0
    Quote Originally Posted by rocket rod View Post
    I've installed the load resistor onto the RHS car indicator
    The car indicators are on a separate circuit to the trailer indicators. The load resistor will need to be in parallel with the trailer indicator. You could put it in the car, but it needs to be from the trailer indicator circuit to earth. If switched on it should indicate a trailer attached even when its not there.

    regards
    Gerry
    Reply With Quote Reply With Quote
  9. 13th April 2019, 12:24 AM #39
    rocket rod
    rocket rod is offline Master Subscriber
    Join Date
    Jun 2009
    Location
    Perth
    Posts
    576
    Total Downloaded
    1.13 MB
    Quote Originally Posted by disco4now View Post
    The car indicators are on a separate circuit to the trailer indicators. The load resistor will need to be in parallel with the trailer indicator. You could put it in the car, but it needs to be from the trailer indicator circuit to earth. If switched on it should indicate a trailer attached even when its not there.

    regards
    Gerry
    Damn, I thought that might be the case. Thanks
    Rod

    D4 MY16 5 seat TDV6 - LLAMS, Custom Drawers, OL Bar, Toyo Open Country, GOE Rims, Lithium DBS, eDiff, OA Long Range Tank, GAP Tool, Tracklander rack, Mitch Hitch, TPMS & Safari Snorkel
    Reply With Quote Reply With Quote
Page 4 of 4 FirstFirst ... 234
« resetting oil level indicator( Electronic) | DIY metal pan »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!