Page 4 of 4 FirstFirst ... 234
Results 31 to 38 of 38

Thread: Air Suspension

  1. #31
    BradC is offline Super Moderator
    No one of consequence
    Supporter
    Join Date
    Mar 2018
    Location
    Perth (near Malaga)
    Posts
    3,545
    Total Downloaded
    0
    Quote Originally Posted by loanrangie View Post
    about $5 worth of o-rings there, some one buy the kit then replicate it.
    I'm happy to pay the 30 bucks and reward them for actually making it available, documenting it and supporting their stuff.

  2. #32
    Join Date
    Mar 2016
    Location
    Perth
    Posts
    4,335
    Total Downloaded
    0
    Quote Originally Posted by BradC View Post
    I'm happy to pay the 30 bucks and reward them for actually making it available, documenting it and supporting their stuff.
    Same
    2010 TDV6 3.0L Discovery 4 HSE
    2007 Audi RS4 (B7)

  3. #33
    BradC is offline Super Moderator
    No one of consequence
    Supporter
    Join Date
    Mar 2018
    Location
    Perth (near Malaga)
    Posts
    3,545
    Total Downloaded
    0
    Quote Originally Posted by loanrangie View Post
    about $5 worth of o-rings there, some one buy the kit then replicate it.
    Dimensions are here. Go your hardest.

    Austausch vorderer Ventilblock?

  4. #34
    Join Date
    May 2010
    Location
    Brisbane, QLD, Australia
    Posts
    2,252
    Total Downloaded
    0
    Quote Originally Posted by Andrew67 View Post
    Hi members,

    Thought I would post an update and hopefully help another member in the future,

    After a number of issues the front left airbag needed replacing and this was a very easy job so if your reasonably mechanical I would fit your own. Here's where the real problem came in, I was getting continual venting from the compressor exhaust valve till the D3 hit the bump stops. On the GAP tools live values the pressure would not hold, very erratic, pressure up but the shoot down to mid 200kpa then the compressor would kick in, kept repeating the process. Then the compressor would do a large dump of air when I came to a stop and turned her off.

    So I replaced the central reservoir valve block having found dessicant powder in the pressure valve. The problem remained. So I went back to the beginning of the system and removed and checked the reservoir again very easy to remove and I also checked the line to the reservoir block and this was all good.

    I had just replaced the compressor with a Dunlop aftermarket so this was good also. So up to that point it was all working. I really had suspected the reservoir valve but this wasn't the problem.

    So I went to the next part in the line up and removed the silencer and air filter, this is a total disaster of a job and I would not do this again I would just blow the lines in situ. The air filter is in a ridiculous location and I altered this setup slightly to give better access for future service. My air filter was in need of replacement as the sponge inside had broken down.

    I changed the rear air filter for a quality K/N type, pushes over the rear air hose and you can leave it directly behind the rear left hatch for easy cleaning. Its original location up behind the rear quarter light is just plain ridiculous for access. Putting it back there is nigh on impossible.

    Now I went to each valve block starting with the front which is easy to get to and work on. On closer inspection ( I have already had these out ) the very small rubber o rings had deteriorated so I changed them over. You dont need to order the sets online if your stuck somewhere you can if possible go to a decent engineering place or the like and they will most likely have the same o rings or at least the critical ones. However keeping a rebuild kit in your D3 is a smart idea. Checked the rear valve and the same , not quite as bad but on the way so I replaced the guilty o rings. I'm doing the complete rebuild on the valves now. This was the culprit, immediately the pressure was smoother on the GAP tool, the system went through a couple of cycles which I presume is to build up the reservoir pressure. Once it was at 1600/1700kpa it settled down held right of 330kpa and no more venting only the one D3 fart as its known. The ride is far better now these valves have all been rebuilt. So after all that it was some little rubber o rings with a value of a $ so if your getting some air leaks and done the overnight tests to see if its an airbag then overhaul your valves if you know they haven't been done for a while if ever. Very easy and also a cheap job , I would recommend this as part of your upkeep/servicing.

    When replacing front airbag I used a quality push in connector because supporting the airbag while trying to thread the Voss connector in such a tight space is a fiddly job because you cant get enough slack on the air line to have the air bag low enough for ease of access.

    Also put quality push in connectors on the rear valve block as it too is very fiddly trying to screw Voss connectors in without crossing the plastic valve body thread.

    If you haven't had your inside wheel arch covers off for a while ?? then take them out.....blow your mind how much **** accumulates behind those things : ) mine must be 20 kilos lighter now with all the crap I removed.

    Hope this helps some other unfortunate soul like me,
    Great news mate.

    Question ... are you towing a workshop? Sounded like you have what it takes to rebuild the whole car

    Cheers.

  5. #35
    Join Date
    Dec 2020
    Location
    Coolum Beach
    Posts
    37
    Total Downloaded
    0
    Quote Originally Posted by Eric SDV6SE View Post
    Replaced all 4 air struts at 210000km, next is front LCAs and sway bar tie rods with hd items.

    Air Comp (hitachi) has had a full rebuild and alloy cap. I don't have any air suspension error codes, and car does not drop on any corner even after a week of parked up, so I think all is ok. it was however interesting to read improved ride when reading about the valve block rebuild.

    Would be good to know o ring sizes all round to build a bit of an emergency kit...

    4x4 air seals kit, but if not then dismantle a valve and take the o rings to a decent engineering shop or as I did CBC bearings in Alice, you will get the critical ones that seal the air inside the valves.

  6. #36
    Join Date
    Dec 2020
    Location
    Coolum Beach
    Posts
    37
    Total Downloaded
    0

    Smile

    Quote Originally Posted by Celtoid View Post
    Great news mate.

    Question ... are you towing a workshop? Sounded like you have what it takes to rebuild the whole car

    Cheers.
    I do now : ) I've certainly got a good range of critical spares if I need them

  7. #37
    Join Date
    Dec 2020
    Location
    Coolum Beach
    Posts
    37
    Total Downloaded
    0
    Quote Originally Posted by DiscoJeffster View Post
    Can you elaborate on what connectors you went with instead of VOSS?
    A company called HOSETECH in Alice Springs supply them, very nice quality I will get an accurate name for them

    They have a 6mm push in connection ( HOSETECH also supply the hose if you need some spare ) the thread is same as the Voss obviously.

    Will take some pictures of mine, I have now tested them over a 1,000kms and they have held with no problems.

  8. #38
    Join Date
    Dec 2020
    Location
    Coolum Beach
    Posts
    37
    Total Downloaded
    0
    LR3 PUSH IN Conector.jpgLR3 PUSH IN Conector 1.jpgLR3 Conections.jpgVOSS to Connector to SCHRAEDER VALVE.jpg
    Quote Originally Posted by DiscoJeffster View Post
    Can you elaborate on what connectors you went with instead of VOSS?
    The nickel plated push in connectors are really nice quality, already with PTF tape, they retail for $4 each,

    Hosetech also supply 6mm tube and its good to keep a few meters on board, $2 a meter

    The black plastic T and straight connectors are handy in an emergency or use to setup an individual inflate system for the whole system or individual set up for each airbag. Less than $3 each from memory

    The VOSS to CONNECTION to SCHRAEDER was my setup to inflate the reservoir to test it. Also you could use this to setup individual inflation of each airbag for emergency OR permanent.

    I'm sure plenty of place would stock these I happened to go to HOSETECH in Alice Springs and they were very helpful and I'm sure they would post.

    Hope this helps Andrew67

Page 4 of 4 FirstFirst ... 234

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!