Results 1 to 8 of 8

Thread: I should know better

  1. 8th October 2021, 08:08 PM #1
    Bulletman's Avatar
    Bulletman
    Bulletman is offline Master
    Join Date
    Jan 2020
    Location
    McGowanastan
    Posts
    694
    Total Downloaded
    0

    I should know better

    So got caught buying cheap front wheel bearings, long story... Anyway 12,000ks later and a new set of timken bearings are in my possession, I vaguely remember the nut tension changed about 2017 , it was tight around 300nm but think it’s around 220nm now.

    I did a search but haven’t been able to find a definitive number, could someone please enlighten me on the new tension on the hub nut.

    Thanks in advance
    Cheers Bulletman
    Reply With Quote Reply With Quote
  2. 8th October 2021, 08:36 PM #2
    Eric SDV6SE's Avatar
    Eric SDV6SE
    Eric SDV6SE is offline ChatterBox Subscriber
    Join Date
    Sep 2014
    Location
    Baldivis WA
    Posts
    2,293
    Total Downloaded
    0
    The DIY lower control arm thread on here (sorry don't know how to paste a link in here) stated 350Nm.

    I thought the Advanced Factors site states the hub nut value. Otherwise a quick call to your trusted indie should answer it.

    My question is how do you get them undone and redone to spec? Do you brace off the wheel studs?
    Reply With Quote Reply With Quote
  3. 8th October 2021, 08:41 PM #3
    DiscoJeffster
    DiscoJeffster is offline TopicToaster Subscriber
    Join Date
    Mar 2016
    Location
    Perth
    Posts
    4,335
    Total Downloaded
    0
    Quote Originally Posted by Eric SDV6SE View Post
    The DIY lower control arm thread on here (sorry don't know how to paste a link in here) stated 350Nm.

    I thought the Advanced Factors site states the hub nut value. Otherwise a quick call to your trusted indie should answer it.

    My question is how do you get them undone and redone to spec? Do you brace off the wheel studs?
    Yeah nah. Was dropped by over 100nm but I don’t know the exact figure. 200nm odd is about what I recall.
    The hub nut just does up. There’s no need to brace it off anything.
    2010 TDV6 3.0L Discovery 4 HSE
    2007 Audi RS4 (B7)
    Reply With Quote Reply With Quote
  4. 8th October 2021, 09:16 PM #4
    loanrangie's Avatar
    loanrangie
    loanrangie is offline LordRover Subscriber
    Join Date
    Jan 1970
    Location
    St Helena,Melbourne
    Posts
    16,770
    Total Downloaded
    1.13 MB
    I think it's 230nm.
    MY08 TDV6 SE D3- permagrin ooh yeah
    2004 Jayco Freedom tin tent
    1998 Triumph Daytona T595
    1974 VW Kombi bus
    1958 Holden FC special sedan
    Reply With Quote Reply With Quote
  5. 8th October 2021, 09:57 PM #5
    Bulletman's Avatar
    Bulletman
    Bulletman is offline Master
    Join Date
    Jan 2020
    Location
    McGowanastan
    Posts
    694
    Total Downloaded
    0
    Quote Originally Posted by Eric SDV6SE View Post
    The DIY lower control arm thread on here (sorry don't know how to paste a link in here) stated 350Nm.

    I thought the Advanced Factors site states the hub nut value. Otherwise a quick call to your trusted indie should answer it.

    My question is how do you get them undone and redone to spec? Do you brace off the wheel studs?
    Leave he wheels on the ground and tighten the nut I would assume.
    Cheers Bulletman
    Reply With Quote Reply With Quote
  6. 8th October 2021, 10:01 PM #6
    BradC
    BradC is online now Super Moderator
    No one of consequence     Supporter
    Join Date
    Mar 2018
    Location
    Perth (near Malaga)
    Posts
    3,546
    Total Downloaded
    0
    Quote Originally Posted by loanrangie View Post
    I think it's 230nm.
    Looks about right : LR014147 LR048083 Optimal Front wheel hub Bearing Kit Discovery 3 & 4 Range Rover Sport RFM500010

    "Hub nut torque has been reduced to 230Nm / 169 lb-ft, correct torque is important."
    Reply With Quote Reply With Quote
  7. 9th October 2021, 12:07 PM #7
    Eric SDV6SE's Avatar
    Eric SDV6SE
    Eric SDV6SE is offline ChatterBox Subscriber
    Join Date
    Sep 2014
    Location
    Baldivis WA
    Posts
    2,293
    Total Downloaded
    0
    Quote Originally Posted by BradC View Post
    Looks about right : LR014147 LR048083 Optimal Front wheel hub Bearing Kit Discovery 3 & 4 Range Rover Sport RFM500010

    "Hub nut torque has been reduced to 230Nm / 169 lb-ft, correct torque is important."
    Yep, so hub retaining bolts (mount to the knuckle) @115Nm and hub to stub shaft @230Nm.

    If tightening with wheel on the ground, need to make sure your socket fits through the centre cap retaining bore.

    Two new front bearings are on my list too. Rear lower arms and bearings to follow soon.....
    Reply With Quote Reply With Quote
  8. 9th October 2021, 05:17 PM #8
    Bulletman's Avatar
    Bulletman
    Bulletman is offline Master
    Join Date
    Jan 2020
    Location
    McGowanastan
    Posts
    694
    Total Downloaded
    0
    Job done today and the difference in the drive of the car is very noticeable. Last time I will get caught buying the inferior wheel bearings, well hopefully I wont have to worry for several years.

    Bulletman
    Reply With Quote Reply With Quote
« Reversing Lights | Original specifications from VIN? »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!