Page 2 of 2 FirstFirst 12
Results 11 to 15 of 15

Thread: Help Needed- Alternator Dead

  1. 4th July 2022, 11:11 AM #11
    Jueylea
    Jueylea is offline Fossicker Subscriber
    Join Date
    May 2018
    Location
    South Australia
    Posts
    28
    Total Downloaded
    0
    Standard Denso has been purchased and collected from TRS in Lonsdale.
    Now to fit at some stage over the next couple of days.
    Thanks for people's input!
    Reply With Quote Reply With Quote
  2. 5th July 2022, 09:14 AM #12
    Porker
    Porker is offline Fossicker Supporter
    Join Date
    Mar 2021
    Location
    Newcastle
    Posts
    46
    Total Downloaded
    0
    Quote Originally Posted by Jueylea View Post
    Standard Denso has been purchased and collected from TRS in Lonsdale.
    Now to fit at some stage over the next couple of days.
    Thanks for people's input!
    Hi, is the part number that you purchased LR072756? As mine just today has started making a screeching noise for about 5-10sec on a cold start too(202k km)
    Thanks Paul.
    Reply With Quote Reply With Quote
  3. 5th July 2022, 09:28 AM #13
    Jueylea
    Jueylea is offline Fossicker Subscriber
    Join Date
    May 2018
    Location
    South Australia
    Posts
    28
    Total Downloaded
    0
    Fitting a Denso DAN1105 which is what I found as standard fitment on the site
    Reply With Quote Reply With Quote
  4. 5th July 2022, 06:57 PM #14
    Jueylea
    Jueylea is offline Fossicker Subscriber
    Join Date
    May 2018
    Location
    South Australia
    Posts
    28
    Total Downloaded
    0
    Had my local mechanic install today. Sounds like a PITA on the SDV6. He felt he had to pull half the front out the car. Ended up having to extend a wire to complete the job which I've read before. Sorry I cannot document the process as it seems it differs quite a bit from the 2.7's.
    Reply With Quote Reply With Quote
  5. 5th July 2022, 10:03 PM #15
    DiscoJeffster
    DiscoJeffster is offline TopicToaster Subscriber
    Join Date
    Mar 2016
    Location
    Perth
    Posts
    4,335
    Total Downloaded
    0
    Quote Originally Posted by Jueylea View Post
    Had my local mechanic install today. Sounds like a PITA on the SDV6. He felt he had to pull half the front out the car. Ended up having to extend a wire to complete the job which I've read before. Sorry I cannot document the process as it seems it differs quite a bit from the 2.7's.
    It’s not easy but not that bad. Nothing had to come out to do mine, but yes, the rear sensor wire is a right pain. It has a connector that for the life of you is impossible to work out from under the car with your hand stretched into that awkward position if you’ve never done it before. It’s why many people just cut the wire, lengthen and solder it - like I did lol.

    It’s still a two hour job for an amateur on the SD.
    2010 TDV6 3.0L Discovery 4 HSE
    2007 Audi RS4 (B7)
    Reply With Quote Reply With Quote
Page 2 of 2 FirstFirst 12
« Alternator - to replace or not? | Power steering pump required URGENT for 2011 D4 in Perth »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!