Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 39

Thread: Cruise - Speed Control Input Voltage

  1. 24th July 2024, 04:33 PM #21
    BradC
    BradC is offline Super Moderator
    No one of consequence     Supporter
    Join Date
    Mar 2018
    Location
    Perth (near Malaga)
    Posts
    3,545
    Total Downloaded
    0
    Check the wiring diagram : Later D3 wiring diagrams

    On the D3 both sides of the brake switch come from separate fuses. I'd assume the 4 is similar but the wiring diagram is the way to enlightenment.

    Edit : And I'd be wrong. S215 on the diagram. Brake light side (NO) goes from Fuse 14P to the BCM (brake light power). The NC side goes from the ECM to ground.
    MY08 D3 - The Antichrist - "Permagrimace". Turn the key and play the "will it get me home again" lottery.
    Reply With Quote Reply With Quote
  2. 24th July 2024, 04:56 PM #22
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    Can the IIDtool monitor the status of the CC enable and CC cancel buttons?
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  3. 24th July 2024, 05:16 PM #23
    BradC
    BradC is offline Super Moderator
    No one of consequence     Supporter
    Join Date
    Mar 2018
    Location
    Perth (near Malaga)
    Posts
    3,545
    Total Downloaded
    0
    Quote Originally Posted by Graeme View Post
    Can the IIDtool monitor the status of the CC enable and CC cancel buttons?
    It must be able to. That's its primary user interface.

    Edit : On the D3 under TDV6 ECM it's the "Speed Control Input Voltage". That gives the voltage on the resistor ladder for the 6 CC buttons. Mine idles at about 4.1V.
    MY08 D3 - The Antichrist - "Permagrimace". Turn the key and play the "will it get me home again" lottery.
    Reply With Quote Reply With Quote
  4. 24th July 2024, 05:22 PM #24
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    My expectations, but my L322 might be different so a check might not be valid for a D4.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  5. 24th July 2024, 05:48 PM #25
    BradC
    BradC is offline Super Moderator
    No one of consequence     Supporter
    Join Date
    Mar 2018
    Location
    Perth (near Malaga)
    Posts
    3,545
    Total Downloaded
    0
    Shoulda checked the wiring diagram. The D4 audio side controls are a resistor ladder same as the 3, but it looks like the cruise switches and flappy paddles connect to a LIN module which goes to the BCM. On that note, I'll back away slowly.
    MY08 D3 - The Antichrist - "Permagrimace". Turn the key and play the "will it get me home again" lottery.
    Reply With Quote Reply With Quote
  6. 24th July 2024, 09:05 PM #26
    Skmitchell91
    Skmitchell91 is offline Fossicker
    Join Date
    Jun 2024
    Location
    Berry, NSW
    Posts
    15
    Total Downloaded
    0
    Quote Originally Posted by BradC View Post
    It must be able to. That's its primary user interface.

    Edit : On the D3 under TDV6 ECM it's the "Speed Control Input Voltage". That gives the voltage on the resistor ladder for the 6 CC buttons. Mine idles at about 4.1V.
    I'm not getting any voltage reading which is where i guess my issue lays. But i'm getting voltage into the clock spring, and i've put a new clockspring in...interesting
    Reply With Quote Reply With Quote
  7. 24th July 2024, 09:50 PM #27
    BradC
    BradC is offline Super Moderator
    No one of consequence     Supporter
    Join Date
    Mar 2018
    Location
    Perth (near Malaga)
    Posts
    3,545
    Total Downloaded
    0
    Quote Originally Posted by Skmitchell91 View Post
    I'm not getting any voltage reading which is where i guess my issue lays. But i'm getting voltage into the clock spring, and i've put a new clockspring in...interesting
    It looks like the D4 uses a little processor in the steering wheel and a one wire LIN bus to the BCM, so you won't see a voltage in the GAP. It'll be an asynchronous serial connection.

    Now, easy test is plug the GAP in and try to use its dashboard interface. It's navigated with the cruise control buttons. If that works the problem is elsewhere.
    MY08 D3 - The Antichrist - "Permagrimace". Turn the key and play the "will it get me home again" lottery.
    Reply With Quote Reply With Quote
  8. 25th July 2024, 05:53 AM #28
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    The switches have been known to fail.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  9. 25th July 2024, 06:49 AM #29
    Skmitchell91
    Skmitchell91 is offline Fossicker
    Join Date
    Jun 2024
    Location
    Berry, NSW
    Posts
    15
    Total Downloaded
    0
    Quote Originally Posted by Graeme View Post
    The switches have been known to fail.
    Guess a new switch pack is on the card then

    Put on the GAP and it's not showing any of the Set Speed buttons as being pushed, strange that all would fail at once. I'll try to chase down a loom too i guess, do all at once
    Reply With Quote Reply With Quote
  10. 25th July 2024, 07:05 AM #30
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    I have a recollection of the existance a loom connecting both switches and therefore the right switch bank may have an impact, but I may be confusing the D4 with my L322 to which I retro-fitted ACC which required a different left switch bank.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
Page 3 of 4 FirstFirst 1234 LastLast
« Landrover D4 Snorkel | Air Suspension Auto Raise to Extended Issue »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!