Results 1 to 7 of 7

Thread: Wiring, D3 bumper mounted fog lights

  1. 11th April 2008, 03:35 AM #1
    rovers1952's Avatar
    rovers1952
    rovers1952 is offline Master
    Join Date
    Apr 2008
    Location
    Sydney
    Posts
    124
    Total Downloaded
    0

    Wiring, D3 bumper mounted fog lights

    Have arranged fittment of ARB Bull Bar. Like the steering wheel mounted radio buttons, Was wondering if fog light wiring is in place behind bumper of my TDV6S If so thought I could purchase the lights to be fitted to the Bar rather than the blanking plates. Anyone have any thoughts?
    Reply With Quote Reply With Quote
  2. 11th April 2008, 09:05 AM #2
    Tote's Avatar
    Tote
    Tote is offline ForumSage Subscriber
    Join Date
    Feb 2007
    Location
    Yass NSW
    Posts
    5,599
    Total Downloaded
    0
    If you went the factory wiring route you would need the headlight switch that pulls out two positions to activate front and rear fog lights as well, don't know if the S has this.
    Regards,
    Tote
    Reply With Quote Reply With Quote
  3. 11th April 2008, 11:28 AM #3
    rovers1952's Avatar
    rovers1952
    rovers1952 is offline Master
    Join Date
    Apr 2008
    Location
    Sydney
    Posts
    124
    Total Downloaded
    0
    thanks & yep....headlight switch is configured as described....presume it is wired at that end!!
    Reply With Quote Reply With Quote
  4. 12th April 2008, 08:43 PM #4
    sniegy's Avatar
    sniegy
    sniegy is offline ChatterBox
    Join Date
    Jan 1970
    Location
    Melbourne
    Posts
    2,622
    Total Downloaded
    0
    Hi Rovers1952,
    Just want to check the head light switch again. Are u sure it pulls out "2" positions & not 1. All the "S" models i have seen the switch only pulls out 1 position. Therefore u would need to replace the switch with an SE variant & reconfigure vehicle with front fog lights.
    Reply With Quote Reply With Quote
  5. 13th April 2008, 04:55 AM #5
    rovers1952's Avatar
    rovers1952
    rovers1952 is offline Master
    Join Date
    Apr 2008
    Location
    Sydney
    Posts
    124
    Total Downloaded
    0
    H'mmmm....I checked again....yup....only pulls out one position to activate the rear so called bad weather lights. Seems silly to not have the front & rear in the same circuit. Presumably the wiring provision is in place.
    Reply With Quote Reply With Quote
  6. 14th April 2008, 12:42 PM #6
    sniegy's Avatar
    sniegy
    sniegy is offline ChatterBox
    Join Date
    Jan 1970
    Location
    Melbourne
    Posts
    2,622
    Total Downloaded
    0
    The part number for this component is YUD501480PVJ
    I had a play this morning & plugged an SE variant in & it all worked. But remember the wiring loom only goes to behind the R/H/F headlight, so the rest that sits in between the bumper u will have to make up yourself.

    Cost of switch pack is approx $110.00 incl GST.
    Last edited by sniegy; 14th April 2008 at 06:36 PM. Reason: Incorrect p/no.
    Reply With Quote Reply With Quote
  7. 15th April 2008, 04:28 AM #7
    rovers1952's Avatar
    rovers1952
    rovers1952 is offline Master
    Join Date
    Apr 2008
    Location
    Sydney
    Posts
    124
    Total Downloaded
    0
    most usefull Sneigy. Am getting a spare spare wheel & tyre from a recycler in Adelaide. They seem to get the desert rollovers. Will try them for lights & switch. Many thanks
    Reply With Quote Reply With Quote
« Snorkel? | Is the TDV6 "S" ok for Offroad »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!