Page 2 of 9 FirstFirst 1234 ... LastLast
Results 11 to 20 of 90

Thread: The P38 Rear Bar Tyre Carrier SNAFU

  1. 4th March 2013, 08:36 AM #11
    bobslandies
    bobslandies is offline AT REST
    Join Date
    Jul 2006
    Location
    Seaforth NSW
    Posts
    933
    Total Downloaded
    0
    Quote Originally Posted by benji View Post
    Michael Samootin is his name. Myself and a few others bought rear bars off him in I think September last year.

    If you take a look back at the old thread there's a flyer and prices.

    A great bar, well finished, and extremely solid.

    I doubt a D2 bar could be modified, as there is about 200mm difference in the chassis width.

    When I got mine I had the same conundrum. I made up a frame from 25X3 SHS that bolts into the two floor bosses on the drivers side in the boot, braced up to the tire. I'll post a few photos up. It wouldn't hold in a severe accident though.
    Thanks benji for the clue how long ago it was. My friend got one and I know it has been sitting around a while as he could not do the fitting himself (bad back) and was waiting for Peter Davis to fit it for him. Looks great too! He's added an upright for a reversing light and backing camera.

    http://www.aulro.com/afvb/p38a-range...ar-bars-2.html
    Flyer at p2 post #12 - benji.

    Bob
    Reply With Quote Reply With Quote
  2. 4th March 2013, 11:01 AM #12
    Keithy P38's Avatar
    Keithy P38
    Keithy P38 is offline AT REST
    Join Date
    Feb 2010
    Location
    Townsville, QLD
    Posts
    2,581
    Total Downloaded
    0
    As mentioned in that post, you end up paying over $3k for a dual wheel carrier equipped rear bar... Could get one made up for half that...
    Reply With Quote Reply With Quote
  3. 4th March 2013, 01:31 PM #13
    bobslandies
    bobslandies is offline AT REST
    Join Date
    Jul 2006
    Location
    Seaforth NSW
    Posts
    933
    Total Downloaded
    0
    As I said there was a special offer last year and my friend bought a rear bar / single wheel carrier, fitted with extra stub and clamp on P/S for future use. It cost under $2700 delivered to Sydney.

    Apparently the Kaymar unit is no longer available and Ron got one of these ones also as he was more impressed with its design and quality (having had a Kaymar).

    Bob
    Reply With Quote Reply With Quote
  4. 4th March 2013, 02:35 PM #14
    Vern's Avatar
    Vern
    Vern is offline OldBushie
    Join Date
    May 2006
    Location
    Woolgoolga
    Posts
    7,870
    Total Downloaded
    0
    Look at Gippslander on here, he made his own, looks neat.
    Reply With Quote Reply With Quote
  5. 4th March 2013, 07:07 PM #15
    TheTree
    TheTree is offline ChatterBox
    Join Date
    Feb 2013
    Location
    Gosford, NSW, Australia
    Posts
    2,556
    Total Downloaded
    0
    Looks like the gippslander idea is the go, 3k for a rear bar is a bit rich for me
    Reply With Quote Reply With Quote
  6. 4th March 2013, 08:02 PM #16
    Keithy P38's Avatar
    Keithy P38
    Keithy P38 is offline AT REST
    Join Date
    Feb 2010
    Location
    Townsville, QLD
    Posts
    2,581
    Total Downloaded
    0
    Yeah, I rekon even an "expensive" metal fab joint would charge less...

    Ill be getting a quote in August from my guys!
    Reply With Quote Reply With Quote
  7. 4th March 2013, 08:28 PM #17
    PaulP38a's Avatar
    PaulP38a
    PaulP38a is offline Wizard Gold Subscriber
    Join Date
    May 2008
    Location
    Canberra
    Posts
    1,834
    Total Downloaded
    0
    I transferred my 4.5yo 4x4 intelligence rear bar from my (now sold) Hard Rangie to my black P38 a couple of weeks ago, and was impressed how well it still looked overall. A couple of minor irritations with the wheel carrier open/close strut mount, but nothing to make me regret paying around $2.3-2.5k for it a few years back.
    My toys, projects and write-ups at PaulP38a.com
    Reply With Quote Reply With Quote
  8. 5th March 2013, 08:14 AM #18
    TheTree
    TheTree is offline ChatterBox
    Join Date
    Feb 2013
    Location
    Gosford, NSW, Australia
    Posts
    2,556
    Total Downloaded
    0
    Hey Paul,

    I hear you regarding the quality and longevity of this bar, but for me it's just a bit OTT for a wheel carrier!
    Reply With Quote Reply With Quote
  9. 7th March 2013, 09:10 AM #19
    Robsrod 58
    Robsrod 58 is offline Master
    Join Date
    Apr 2012
    Location
    Engadine NSW
    Posts
    204
    Total Downloaded
    0
    I'm in the process of getting a quote for a custom one using "Rigidig" parts from a guy in Taren Point, Sydney. I'll post quote when received.
    Reply With Quote Reply With Quote
  10. 14th March 2013, 04:30 PM #20
    p38arover's Avatar
    p38arover
    p38arover is offline Major part of the heart and soul of AULRO.com
    Administrator
    I'm here to help you!     Gold Subscriber
    Join Date
    Jan 1970
    Location
    Western Sydney
    Posts
    30,707
    Total Downloaded
    1.63 MB
    I have a swingaway rear wheel carrier on a rear bar but I must admit I like this idea: RPi Engineering - Specialized Rover Engines - faqs

    Ron B.
    VK2OTC

    2003 L322 Range Rover Vogue 4.4 V8 Auto
    2007 Yamaha XJR1300
    Previous: 1983, 1986 RRC; 1995, 1996 P38A; 1995 Disco1; 1984 V8 County 110; Series IIA



    RIP Bucko - Riding on Forever
    Reply With Quote Reply With Quote
Page 2 of 9 FirstFirst 1234 ... LastLast
« P38A weird electrical door module ticking | Stacker gone »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!