Page 1 of 39 12311 ... LastLast
Results 1 to 10 of 385

Thread: V8 county ute

  1. 1st December 2016, 07:13 PM #1
    fitzy
    fitzy is offline Master
    Join Date
    May 2009
    Posts
    981
    Total Downloaded
    0

    V8 county ute

    My first landy was a11a workshopimage.jpg
    Reply With Quote Reply With Quote
  2. 1st December 2016, 07:29 PM #2
    fitzy
    fitzy is offline Master
    Join Date
    May 2009
    Posts
    981
    Total Downloaded
    0
    Then I got one of these
    And then did a bit of this with it.
    Until it was broken.
    Reply With Quote Reply With Quote
  3. 1st December 2016, 07:32 PM #3
    fitzy
    fitzy is offline Master
    Join Date
    May 2009
    Posts
    981
    Total Downloaded
    0
    Then I bought this
    Here it is with the others
    Last edited by p38arover; 5th July 2017 at 07:26 AM.
    Reply With Quote Reply With Quote
  4. 1st December 2016, 07:35 PM #4
    fitzy
    fitzy is offline Master
    Join Date
    May 2009
    Posts
    981
    Total Downloaded
    0
    Seeing as I already have a wagon and a dual cab work ute I might build a ute. With a bit of inspiration from rovercare's effort I have had the engineer visit so let the fun begin.
    Reply With Quote Reply With Quote
  5. 1st December 2016, 07:43 PM #5
    fitzy
    fitzy is offline Master
    Join Date
    May 2009
    Posts
    981
    Total Downloaded
    0
    Reply With Quote Reply With Quote
  6. 1st December 2016, 07:47 PM #6
    fitzy
    fitzy is offline Master
    Join Date
    May 2009
    Posts
    981
    Total Downloaded
    0
    A bit of my inspiration and where I'm heading
    Reply With Quote Reply With Quote
  7. 2nd December 2016, 06:01 AM #7
    fitzy
    fitzy is offline Master
    Join Date
    May 2009
    Posts
    981
    Total Downloaded
    0
    The car is a 1985 v8 county with 485,000 k's, I bought it about 3 years ago and swapped most of the drivetrain from the Rangie into it.
    As it sits now it has
    3.5 rv8 with 14 cux
    Zf auto
    Lt230 with 1.4:1 high and 30% maxidrive low range
    Laminated front housing with rotated swivels and maxi locker and early range 2 piece cv's, 110 brakes
    Open Sals rear with drums,
    Reply With Quote Reply With Quote
  8. 3rd December 2016, 04:25 PM #8
    fitzy
    fitzy is offline Master
    Join Date
    May 2009
    Posts
    981
    Total Downloaded
    0

    V8 county ute

    Thanks to lands864 I got this
    I also had one of these off the 2a

    A test fit
    Last edited by p38arover; 5th July 2017 at 07:27 AM.
    Reply With Quote Reply With Quote
  9. 3rd December 2016, 04:54 PM #9
    fitzy
    fitzy is offline Master
    Join Date
    May 2009
    Posts
    981
    Total Downloaded
    0
    I'm going to keep the B pillar and have made up another B pillar shaped infill piece to extend the cab 100 mm
    Reply With Quote Reply With Quote
  10. 3rd December 2016, 04:56 PM #10
    fitzy
    fitzy is offline Master
    Join Date
    May 2009
    Posts
    981
    Total Downloaded
    0
    I needed to straighten it out after the heat
    Then add some crush tubes
    Reply With Quote Reply With Quote
Page 1 of 39 12311 ... LastLast
« Rebuild D2 ZF Selector Switch UHB100190 | 130 Station Wagon with side fold pop top build »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!