350 to 95 disco

Quote:

---

Originally Posted by rovercare

Well the spigot adaptor is out:eek: total time........probably 6 bloody hours, how did we finally do it after I turned up a decent shaft more grease and bash, then steering wheel puller and harmonic balance puller

https://www.aulro.com/afvb/images/im...2008/02/17.jpg

Nothing a MIG can't fix:D

Lesson 2, whenever you pull the bellhousing of a ZF, don't knock the front housing and pump off, it takes another 1.5hrs to line it up and refit it, try lining 2 sets of clutches up and a splined section, I was about to throw my first violent wobbly in near 6 years after that:eek:

Productive day? well, I'm where I'd of liked to have been yesterday:mad:

---

Did you try the wet toilet paper, much denser than grease, has always worked for me, even when slide hammers failed, Regards Frank.

Quote:

---

Originally Posted by rovercare

Lesson 2, whenever you pull the bellhousing of a ZF, don't knock the front housing and pump off, it takes another 1.5hrs to line it up and refit it, try lining 2 sets of clutches up and a splined section, I was about to throw my first violent wobbly in near 6 years after that:eek:

---

We have had that problem here, with about the same amount of time invested in refitting it!

FMD thats scarey, what sort of oil cooler are you going to use for that poor gearbox?

Quote:

---

Originally Posted by Tank

Did you try the wet toilet paper, much denser than grease, has always worked for me, even when slide hammers failed, Regards Frank.

---

Sorry Frank I didn't see your post before hand, will keep it mind, although grease has always worked for me, The reason it didn't work though, is it only acting on a 3mm surface inside there, trying to push out near 2"s of contact area:)

Quote:

---

Originally Posted by PeterM

Interesting thread. Curious to see how it all goes.

Just to clarify, driveline wise you've got landcruiser centres, hilux cvs and the rest is std rover gear or have you got Maxi axles etc. Rover hubs? Is the 350 a ULP motor? EFI or carbs?

---

Hilux centres and CV's, 3 Jacmac axles, and one short side 60 series

350 Has got an impco 425 mixer at the moment, but will get a quadrajet and probably 225 mixer, it will be gas mainly

Quote:

---

Originally Posted by dobbo

FMD thats scarey, what sort of oil cooler are you going to use for that poor gearbox?

---

Original, it'll be fine;)

Dobbo, What nationality are you???
Only because i say FMD also........ its not a Skip term...

What happened today? well a jag with a 1UZ-FE got dropped off and I have to wire it:eek: so sticky nosed at that for a bit

https://www.aulro.com/afvb/images/im.../2008/02/1.jpg
https://www.aulro.com/afvb/images/im...11/01/1052.jpg
https://www.aulro.com/afvb/images/im...008/03/620.jpg

Then I decided I didn't want to fit the Chev, till a mate bores some holes through the flywheel, for access to the torque convertor bolts, will make for easier removal/refit..........not that it'll be needed:angel::D, so its pulling looms apart till tomorrow arvo then off to bore some holes, see if there is any updates before I go back to work Sunday morning:mad:

Quote:

---

Originally Posted by sclarke

Dobbo, What nationality are you???
Only because i say FMD also........ its not a Skip term...

---

i would say its an aussie term .

Updates.......Anyone interested?:confused:

Well today starts with the Jag, the loom after a hair cut:D

https://www.aulro.com/afvb/images/im...008/03/695.jpg

The Supervision, nearly 17 years old and still kicking along well:eek:

https://www.aulro.com/afvb/images/im...09/01/1466.jpg

Yep, it runs;)

https://www.aulro.com/afvb/images/im...11/01/1051.jpg

What I got done on the Disco, well got the access holes bored for the convertor bolts, that's it:(
https://www.aulro.com/afvb/images/im...008/03/696.jpg