Results 1 to 7 of 7

Thread: Missing vacuum advance pipe

  1. 9th March 2018, 08:02 PM #1
    Dark61's Avatar
    Dark61
    Dark61 is offline ChatterBox Supporter
    Join Date
    Jan 2013
    Location
    Molesworth,Tasmania
    Posts
    2,399
    Total Downloaded
    0

    Missing vacuum advance pipe

    On the 57 88 with an unidentified stromberg - was looking around in the engine bay today and noticed there is no vacum advance pipe. Cant actually see anywhere on the carby where it might have exited either so may be blanked off? Has been sat in a stable for three years - fired up almost 1st start with fresh fuel and a good battery. Runs okish , bit lumpy and slight hunting. Havent touched anything. Coil runs very hot after say 5 mins stationary. My question is should i fit a vacum advance pipe if i can find a point on the carby - and is the hot coil a symptom of no va pipe or has the coil just had it. I’m just driving this around the property picking up wood etc - its not road going.
    All comments gratefully received as usual.
    cheers,
    D
    1957 88 Petrol (Chumlee)
    1960 88 Petrol (Darwin)
    1975 88 Diesel (Mutley)
    Reply With Quote Reply With Quote
  2. 9th March 2018, 09:29 PM #2
    JDNSW's Avatar
    JDNSW
    JDNSW is offline RoverLord Silver Subscriber
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    29,667
    Total Downloaded
    0
    I can't remember where the vacuum pickup is on the Solex, but it is likely not available on the Stromberg. I would suspect the coil is getting hot because it is one designed to be used with a ballast, not used on Series Landrovers. In other words, it is an 8volt coil, not a 12volt one.
    John

    JDNSW
    1986 110 County 3.9 diesel
    1970 2a 109 2.25 petrol
    Reply With Quote Reply With Quote
  3. 10th March 2018, 02:19 PM #3
    1950landy's Avatar
    1950landy
    1950landy is offline YarnMaster Supporter
    Join Date
    Sep 2012
    Location
    Westlake ,brisbane
    Posts
    3,922
    Total Downloaded
    0
    450px-Carby_0_LI (2).jpg On Stromberg the vacuum advance line fits into the brass fitting at base of carby.

    IMAG1921.jpg On the Solex the vacuum advance screws into a taped thread in the base just above were the carby bolts to the manifold.
    Reply With Quote Reply With Quote
  4. 10th March 2018, 02:31 PM #4
    rover-56's Avatar
    rover-56
    rover-56 is offline Master Subscriber
    Join Date
    Nov 2008
    Location
    Bruthen, Eastern Vic.
    Posts
    842
    Total Downloaded
    0
    Mines been missing from my '56 for the last 20 years. Still get about 18-20mpg.
    Doesn't make a lot of difference on a S1 because the throttle pedal is usually on the floor anyway
    RE the coil most likely an 8v coil, as John said.
    Cheers,
    Terry
    Reply With Quote Reply With Quote
  5. 10th March 2018, 04:47 PM #5
    Dark61's Avatar
    Dark61
    Dark61 is offline ChatterBox Supporter
    Join Date
    Jan 2013
    Location
    Molesworth,Tasmania
    Posts
    2,399
    Total Downloaded
    0
    Thanks Gents. Pics always useful.
    I’ll go take another look now i know where i should be looking.
    Should i be blanking the vacum advance off at the dizzy or does it make no difference, blanked off or not blanked off.
    cheers,
    D
    1957 88 Petrol (Chumlee)
    1960 88 Petrol (Darwin)
    1975 88 Diesel (Mutley)
    Reply With Quote Reply With Quote
  6. 10th March 2018, 05:11 PM #6
    JDNSW's Avatar
    JDNSW
    JDNSW is offline RoverLord Silver Subscriber
    Join Date
    Jan 1970
    Location
    Central West NSW
    Posts
    29,667
    Total Downloaded
    0
    No difference.
    John

    JDNSW
    1986 110 County 3.9 diesel
    1970 2a 109 2.25 petrol
    Reply With Quote Reply With Quote
  7. 10th March 2018, 09:50 PM #7
    Dark61's Avatar
    Dark61
    Dark61 is offline ChatterBox Supporter
    Join Date
    Jan 2013
    Location
    Molesworth,Tasmania
    Posts
    2,399
    Total Downloaded
    0

    Further

    These are the pics of the current set up. I can see the vacum advance is blanked off at the carby - not at the dizzy. Thanks again.
    cheers,
    D
    Attached Images Attached Images
    1957 88 Petrol (Chumlee)
    1960 88 Petrol (Darwin)
    1975 88 Diesel (Mutley)
    Reply With Quote Reply With Quote
« Should head bolts be changed? | Hose Air Filter to Carby »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!