Page 2 of 2 FirstFirst 12
Results 11 to 18 of 18

Thread: Ashcroft transfer case kit

  1. #11
    Join Date
    Jul 2010
    Location
    The Grampians
    Posts
    308
    Total Downloaded
    0
    Quote Originally Posted by isuzurover View Post
    ...not sure if Ashcroft still do the kits? Next would be a roverdrive, then diffs.
    Ashcroft certainly still make the kits.

    Ashcroft Transmissions - High Ratio Transfer Case Kit

    They claim "This kit was developed as a stronger alternative to the Series "overdrive." By using the High Ratio conversion the High range is raised by 31.8% (overdrive is 27.5%) whilst leaving Low range unchanged."
    Reuben - I don't have a life I have a Land Rover

    SIII 'Blue Bertha'

  2. #12
    hesguitar Guest
    They certainly do and with the current exchange rate they're a reasonable deal
    i was quoted 330 pounds including core deposit (or send the old case back) plus 90 pounds postage ($680 aus all up) direct from Ashcroft.

    Although after some consultation and consideration (once again thanks for the advice) the high speed transfer kit won't work for ours as it has the standard six, an overdrive will have to be saved up for.

  3. #13
    Join Date
    Jul 2010
    Location
    The Grampians
    Posts
    308
    Total Downloaded
    0
    Fair enough. Yes that price proved irresistible to me. Hopefully it was worth it. I needed to get rid of a very loud and whining overdrive since I didn't want to rebuild it and then find it was still loud and whiny.
    Reuben - I don't have a life I have a Land Rover

    SIII 'Blue Bertha'

  4. #14
    Join Date
    Aug 2006
    Location
    WA
    Posts
    13,786
    Total Downloaded
    0
    Quote Originally Posted by reubsrover View Post
    Ashcroft certainly still make the kits.

    Ashcroft Transmissions - High Ratio Transfer Case Kit

    They claim "This kit was developed as a stronger alternative to the Series "overdrive." By using the High Ratio conversion the High range is raised by 31.8% (overdrive is 27.5%) whilst leaving Low range unchanged."
    You misunderstood me. I was asking if Ashcroft still did the kit to fit an LT77 5-speed into a series. IMHO this option is a hundred times better than fitting a HRTC.

  5. #15
    Join Date
    May 2007
    Location
    Scarborough QLD
    Posts
    524
    Total Downloaded
    0
    They still do them but they are out of stock Ashcroft

    Ivan

  6. #16
    Join Date
    Jul 2010
    Location
    The Grampians
    Posts
    308
    Total Downloaded
    0
    Quote Originally Posted by isuzurover View Post
    You misunderstood me. I was asking if Ashcroft still did the kit to fit an LT77 5-speed into a series. IMHO this option is a hundred times better than fitting a HRTC.

    Ah yes it appears I did . Well I'll soon see if I regret the HRTC purchase, hopefully by next week she'll be back on the road.
    Reuben - I don't have a life I have a Land Rover

    SIII 'Blue Bertha'

  7. #17
    Join Date
    Oct 2010
    Location
    Dixons Creek Victoria
    Posts
    1,533
    Total Downloaded
    0
    If your vehicle is heavy and/or you do a bit of towing, the 31% permanently higher gearing will eventually kill an already marginal gearbox, regardless of engine fitted. At the top of the list of series 1,2, and 2a gearbox weaknesses is the layshaft. When pulling in 2nd gear the gears tend to slightly push away from each other, flexing the non too rigid layshaft until fatigue sets in and the shaft breaks, leaving you with only 4th gear.With higher transfer or diff gears fitted 2nd gear will see alot more use.
    Wagoo.

  8. #18
    Join Date
    Oct 2003
    Location
    Godwin Beach Qld
    Posts
    8,688
    Total Downloaded
    0
    G'day Hesguitar

    My prefered option would be the overdrive unit, more expensive but it is easily removable,(take old output gear and cover as spares to return to standard if required) it gives you more gears if used correctly 2+ 3+ 4+ BUT ALWAYS use the CLUTCH when changing up or down, I have seen so many O/d's destroyed by just pulling in and out, they are not Laycock-De-Normanville, or similar, they also have their own sump and if neglected will overheat and seize, I would also adivse the use of "Wynnes Friction Proofing" or a % of Viscoutine in the O/dr sump.

    From memory the max torque on the IOE 6 cyl is @ 1900-2000 rpm is is a long stroke slow revving high torque slugger but thirsty.


    Hope that is of some help.


    cheers

Page 2 of 2 FirstFirst 12

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!