Reply With Quotewhat do you call no gap?
1/2" ?
YarnMaster
was wondering if someone (probably rocket! :roll: )could tell me why the bellhousng /x member clearance is like minimal if not nothing ?i have jacked up both front of motor and rear of gearbox and not found any signs of a broken mount ,is there a way to adjust the mounts on the body/motor/gearbox as i think this mite be contributing a slight bit of body noise? :?
SysAdmin (Owner)
what do you call no gap?
1/2" ?
2007 Discovery 3 SE7 TDV6 2.7
2012 SZ Territory TX 2.7 TDCi
"Make the lie big, make it simple, keep saying it, and eventually they will believe it." -- a warning from Adolf Hitler
"If you don't have a sense of humour, you probably don't have any sense at all!" -- a wise observation by someone else
'If everyone colludes in believing that war is the norm, nobody will recognize the imperative of peace." -- Anne Deveson
“What you leave behind is not what is engraved in stone monuments, but what is woven into the lives of others.” - Pericles
"We can ignore reality, but we cannot ignore the consequences of ignoring reality.” – Ayn Rand
"The happiness of your life depends upon the quality of your thoughts." Marcus Aurelius
YarnMaster
well i tried to put a small piece of rubber mat in there and had to lever the gearbox up to fit it in ,clearance would be less than 5 mill :!:
SysAdmin (Owner)
that is too close [img]style_emoticons/<#EMO_DIR#>/tongue.gif[/img]
i have seen many conversions that do come that close.
all you can do is pack the mounts with shims where needed and get a happy medium if you can.
2007 Discovery 3 SE7 TDV6 2.7
2012 SZ Territory TX 2.7 TDCi
"Make the lie big, make it simple, keep saying it, and eventually they will believe it." -- a warning from Adolf Hitler
"If you don't have a sense of humour, you probably don't have any sense at all!" -- a wise observation by someone else
'If everyone colludes in believing that war is the norm, nobody will recognize the imperative of peace." -- Anne Deveson
“What you leave behind is not what is engraved in stone monuments, but what is woven into the lives of others.” - Pericles
"We can ignore reality, but we cannot ignore the consequences of ignoring reality.” – Ayn Rand
"The happiness of your life depends upon the quality of your thoughts." Marcus Aurelius
Swaggie
On a similar topic, my front engine mounts are too high, is there an easy way to lowwer them? I'm hesitant to get thinner parts for fear of the vibrations cracking the engine mounts. Am I better to get lowwer engine mounts?
1994 Discovery TDi
2004 Discovery 2 TD5
2010 Discovery 4 TDV6
1961, Series 2 Ambulance. 108-098 - Eden
Registry of Ex Military Land Rovers Mem. 129
Defence Transport Heritage Tasmania Member
YarnMaster
[img]style_emoticons/<#EMO_DIR#>/laugh.gif[/img] I'll swap my lowies for your highies!!!!!
sounds sorta strange and wierd dont it????? :?
AT REST
Hi Ferno
Sounds like you may have the wrong engine mounts in the front, there is a difference between the petrol and diesel, the 21/4 petrol front mounts are P/n NRC 2054 (round steel/rubber/steel,) the rear mounts NRC2053 (round steel/rubber/steel, slightly smaller dia.) the front mounts can be used in the rear /g'box position, the diesel mounts are usually square and not as tall to better absorb the diesel vibrations, with the correct mountings you should get at least 1/2 inch between g/box and x-member [img]style_emoticons/<#EMO_DIR#>/smile.gif[/img] these mounts should be approximately 21/2inches high from memory
Posting Permissions
| Search AULRO.com ONLY! |
Search All the Web! |
|---|
|
|
|
Bookmarks