Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: Seat belt securing point

  1. 29th December 2014, 08:26 PM #11
    101RRS's Avatar
    101RRS
    101RRS is online now LordRover Supporter
    Join Date
    Jan 1970
    Location
    Canberra
    Posts
    18,616
    Total Downloaded
    0
    Once you have been to Dickson you will need to go back there unless they say otherwise.

    If the lightweight had not been previous registered in Aust then you needed to go to Dickson but if it had been and was not modified and normal inspection garage could have done it.

    Cheers

    Garry
    REMLR 243

    2007 Range Rover Sport TDV6
    1977 FC 101
    1976 Jaguar XJ12C
    1973 Haflinger AP700
    1971 Jaguar V12 E-Type Series 3 Roadster
    1957 Series 1 88"
    1957 Series 1 88" Station Wagon
    Reply With Quote Reply With Quote
  2. 29th December 2014, 08:26 PM #12
    drifter Guest
    Yeah - they have it listed as a partial and will only check the items they failed on the last visit.
    Reply With Quote Reply With Quote
  3. 21st January 2015, 05:08 AM #13
    Jondavball
    Jondavball is offline Master
    Join Date
    Nov 2010
    Location
    Canberra
    Posts
    160
    Total Downloaded
    0
    As requested please find attached the new, and certified seat belt mounts.
    The holes on the side are the original position (including the two rivet holes to hold the backing plate in place).
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  4. 21st January 2015, 07:36 AM #14
    Phil B
    Phil B is offline Wizard Subscriber
    Join Date
    Feb 2014
    Location
    Sydney
    Posts
    1,073
    Total Downloaded
    0
    Easy solution.
    Strange though that on mine I wasn't allowed to use the top rail for securing the retractable type bracket.
    I had to drop the bracket down and reinforce the bulkhead inside and outside at the securing points.
    More than one way to skin a cat they say.....
    Thanks,
    Phil B

    Custodian of:
    1974 S3 swb wagon (sold)
    1978 S3 swb canvas
    48 749 '88 4x4 Perentie
    1985 County with 4BD1T
    Reply With Quote Reply With Quote
  5. 21st January 2015, 03:32 PM #15
    Lotz-A-Landies's Avatar
    Lotz-A-Landies
    Lotz-A-Landies is offline Super Moderator Gold Subscriber
    Join Date
    Jul 2006
    Location
    East-South-East Girt-By-Sea
    Posts
    17,662
    Total Downloaded
    1.20 MB
    This is the standard location of the inertia reel in SIII 109 (stage 1).



    The panel behind is reinforced with a double skin of aluminium about 75mm x 100mm and is present on many earlier SIII.

    In the 110/Defender it is located in the gap between the rear door and the front of the transom bolted to the top of the tray with a corresponding bracket to the chassis below.

    You won't find me on: faceplant; Scipe; Infragam; LumpedIn; ShapCnat or Twitting. I'm just not that interesting.
    Reply With Quote Reply With Quote
  6. 21st January 2015, 04:54 PM #16
    Phil B
    Phil B is offline Wizard Subscriber
    Join Date
    Feb 2014
    Location
    Sydney
    Posts
    1,073
    Total Downloaded
    0
    Diana
    That is the fixing point I used for my S3 SWB
    Thanks
    Phil B

    Custodian of:
    1974 S3 swb wagon (sold)
    1978 S3 swb canvas
    48 749 '88 4x4 Perentie
    1985 County with 4BD1T
    Reply With Quote Reply With Quote
Page 2 of 2 FirstFirst 12
« Improving performance? | Muslim fanatics.............. »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!