35-36'' tyres legal on Series vehicles or not?

Quote:

---

Originally Posted by LowRanger

Well get ready to put away your big tyres and suspension,as VSI50 is raising its head again in modified form in NSW.And if reports are true,you won't be able to fit 35's

---

What if your vehicle has the equivalent of a 4" lift as standard and runs 35/36" as standard.

Garry

Quote:

---

Originally Posted by LowRanger

Well get ready to put away your big tyres and suspension,as VSI50 is raising its head again in modified form in NSW.And if reports are true,you won't be able to fit 35's or lift the vehicle more than 75mm if you are in a club and 50mm if you are not in a club.Even with an engineers certificate:eek:
And portals will make the total headlight height too high,so they will be out as well:mad:

Wayne

---

For the dedicated,If one is prepared to cut sheetmetal, there is no necessity to raise the suspension on Series/Defender type Landrovers in order to run 35s.
Free standing headlamps are still available, legal to use and could drop the headlight height down by a few inches.Softer, lower springs with polyairs could get the height down a couple more.And as for 35s, I think we've already established that they were a factory option, diameter wise at least.
Wagoo.

Quote:

---

Originally Posted by wagoo

For the dedicated,If one is prepared to cut sheetmetal, there is no necessity to raise the suspension on Series/Defender type Landrovers in order to run 35s.
Free standing headlamps are still available, legal to use and could drop the headlight height down by a few inches.Softer, lower springs with polyairs could get the height down a couple more.And as for 35s, I think we've already established that they were a factory option, diameter wise at least.
Wagoo.

---

Yes Bill,my headlight height is fine,and the body has had the necessary mods to allow fitment of the 35's,BUT the legal fitting of fitting larger tyres to certain models,just because they are fitted to another model by the same manufacturer isn't allowed,as I mentioned earlier,even without a compliance plate,which didn't come into effect in Australia till 1st August 1971,it will be on a model by model basis,not make by make.And a series 2 or 3 FC is not the same model as a series 2 or 3 109.And there were no options for a 110 or Defender.

Wayne

Quote:

---

Originally Posted by garrycol

What if your vehicle has the equivalent of a 4" lift as standard and runs 35/36" as standard.

Garry

---

Gary
If you are talking about a 101,and it is standard,then there are no problems.

Wayne

im guessing a volvo

Good old 101 landy.
Over seas they fit 20 inch mog wheels to gear them up a bit.
I am interested in this a bit as I am going though the new tyre process now.
The MRF 900x16 now fitted were 35 inch dia when new and are now 34 inch worn.
I am replacing them with Simex centepede 36.4 inch dia.
The bar treads are not up to the performance of the vehicle on or off road.
Wagoo what sort of money are you paying for yours >
The new wheels needed for the Simex are the same as the standard 6,5 inch rim but has a extra bit of width to make them 8 inch and this width is to the out side of the wheel.
I figure this would just place me on the correct side of the law.
The Mich Z series to replace the 900x16 measure about 36 inch on a good day , may be when new..
I should be able to get 12 inches under the diff centres with the new set up

Ron. I payed $400 each for the Simex a couple of years ago, same price TSL Q78s I bought ar the same time. Surely they would be cheaper now with the strong Aus dollar?
wagoo.

Quote:

---

Originally Posted by wagoo

Surely they would be cheaper now with the strong Aus dollar?
wagoo.

---

Pigs might fly too.

Though a local tyre dealer I am looking at 500 dollars a pop, fitted and balanced.
I may be able to get them on the net for just over 400 dollars, but I would have to pay three lots of freight at 89 dollars to keep under the one K tax limit for 5 tyres and still pay locally for fitting and balancing.
The local dealer will let me do lay by too.

Quote:

---

Originally Posted by 101 Ron

Though a local tyre dealer I am looking at 500 dollars a pop, fitted and balanced.
I may be able to get them on the net for just over 400 dollars, but I would have to pay three lots of freight at 89 dollars to keep under the one K tax limit for 5 tyres and still pay locally for fitting and balancing.
The local dealer will let me do lay by too.

---

Those prices are out of my league these days.Might preserve the
Simex/Q78s For the few days a year I use my vehicle on sealed roads and run tractor tyres for the remainder of the year.
Wagoo.