Conversion, has anyone done it?

Quote:

---

Originally Posted by Ralf_the_RR

I reckon the 1UZFE is a great engine.

I believe Mr Toyota asked what is the best V8 in the world.
The answer was a Keith Black.
So Mr Toyota said, OK, lets build a smaller version.

Aparently you can sit a 50c piece on it's edge on a rocker cover, and then bring the revs up from idle to 6000 without the coin falling over.

But they lack low down performance. They produce great horsepower and torque higher up the rev range.

I remember reading about one being installed into a hilux.
He had heaps of problems, and cost a fortune.

---

I can sit a 50c piece on edge on the tappet cover of the tdi300

Just need heaps of silver solder to keep it there when i rev er up:D :D :D

A mate of mine had one of these engines and 4 speed autos in a Kingswood ute. Lots of work, but a nice engine/trans combination.

At the back of my mind I have Gen III 5.7 with 6 speed manual floating around. I think that would be pretty good in a Classic Rangie (mine, specifically :twisted: ).

I've found the Gen111's (and the GenIV's) in manual form to be a dissapointment due to the big lack of low down torque. - I would definitly want an auto behind one of these in 4x4.........

Quote:

---

Originally Posted by mark2

I've found the Gen111's (and the GenIV's) in manual form to be a dissapointment due to the big lack of low down torque. - I would definitly want an auto behind one of these in 4x4.........

---

Surely 5.7 or 6 litres of Chev V8 would have at least as much torque down low as a 3.5 litre Rover V8. If not, it would just be a matter of correct cam selection to cure it.

Ok I know of 3 1uz-fe conversions. They all were in tojos.

1st one was into a 4runner, he cooked the 1st motor after having all sorts of teething problems. He replaced the motor as it was cheaper to get another motor than get new head gaskets, had a few more problems due to after market ecu, but is fairly good now.Still has heating issues here & there.

The 2nd one was into an sr5 hilux (3l diesel model) & after 6 months it still isnt on the road. He is using an after market ecu.

The 3rd was into a Bundera. He has fitted his with the standard ecu & with the info from the previous people has has no worries, in & out in 2 weeks & enjoying it.

The key appears to be to use a standard ecu, all though the power gains & control are much better with an after market ecu,, the problems are larger as well.

Hope this helped :D

Quote:
Originally Posted by mark2 https://www.aulro.com/afvb/images/im...016/08/768.jpg
I've found the Gen111's (and the GenIV's) in manual form to be a dissapointment due to the big lack of low down torque. - I would definitly want an auto behind one of these in 4x4.........

Quote:

---

Originally Posted by BigJon

Surely 5.7 or 6 litres of Chev V8 would have at least as much torque down low as a 3.5 litre Rover V8. If not, it would just be a matter of correct cam selection to cure it.

---

They don't actually, mark2 is right. Mate of mine was Holden Qld state mgr, drove everything Holden made or badged, including a specced 4 door SS gen3 with hollinger. It was a real dissapointment, didn't come on song until close to 70k in 1st, clutch felt like an old HQ 1 tonner, and rode like a dray, nothing sporty about it, certainly not a car to punt thru the twisties in. However the fix to the engine's lacklustre low down torque is only a chip away as it's tuned to meet emmisions so is very soft in std form.

Hi all
This may be a dumb question but why not go for the rover 4.6 engine bolts straight in and no problems with egineering. I am only asking because I am thinking of doing this as my 3.9 is on it's last legs thanks to the previous owner not putting coolant in it and it is very corroded. I'm interested in all of your thoughts coz no matter what we do it is expensive.

Cheers Blythe

P.S. not intending to steal the link just curious

Didn't the 4.6 have issues with porous or slipping liners? I was under the impression that the 4.0 is a better motor.

How about a supercharger?

If any of you wouldbe engine swappers are interested in fitting a supercharged 3.9L complete with all looms,ECU and Davis piggyback ECU I could probably provide one :)

AAARRGH
Why is this so hard???
I would prefer a larger capacity engine to a blown one as the N.T. just doesnt have the people to tune and keep it running.

How much more torque does the 4lt produce over the 3.9lt??

Has any one else got info on the 4.6, or is this why the original question on the Jap V8?

I like the idea of the diesel cummins or chev but the extra weight I think would make the cars balance to front heavy.

Blythe :confused: