Thread: Recommended on-road tyre pressures

My '95 Classic is similar, (withouty pulling the bonnet and looking...) around 28 psi front and 38 psi rear. - Same or similar ratio, loaded/unloaded.

When I bought it at 150K, the pressures were close to being equal... and my Viscous coupling died some months later. Can't say if the two are linked, though I suspect the ratio front/rear has a lot to do with the VC's life-span.

Originally Posted by RVR110

I'm curious about the differential between the front and rear tyre pressure recommendations on the tyre placard on the B pillar in my 110 Puma wagon the rear pressures. The recommended pressure for the front tyres is 30psi and for the rear it is 45psi when lightly loaded.

I haven’t had the car on a weigh bridge but I would not have thought that the weight distribution would be skewed to the rear although I may be wrong. Does anyone know why LR would recommend such a marked difference between pressures?

I think you'll find that users of older 110s and deefers generally use substantially lower pressures than those placarded; (for comfort reasons). I know I do.

I imagine that if you experiment with sealed road pressures of 30psi or slightly less all round you may find it more comfortable. Off the tar you may wish to decrease them even further.

I believe that the 45psi is placarded to allow for the massive load carrying capability of the vehicle (which is rarely used)

the Puma has, a version of the LT230 tc so no VC to worry about as in post #2

Hi, "The Land Rover Experience' by Tom Sheppard recommends:
Kerb weight(unloaded) 26psi f and 30psi rear
Max load: 27 front 48 rear
You could use the 4psi rule to fine tune. Pressure should increase by 4psi from cold to warm after a run. If less reduce pressure; if higher increase.
Hope this may be of use. Cheers.

I'm running 26psi front and 28 rear on bitumen, unladen. I have the original tyres and my vehicle has done 18k. I find the recommended pressures make for a harsh ride.
I am aware of a number of rollovers where Rovers have had tyre pressures low in stone and sand conditions.
It seems that tubeless tyre beads can come away from the rim if under inflated and subject to high side load as in a sharp turn.
For unmade roads and for a loaded vehicle I think it is prudent to increase pressures up to 28front and 48 rear depending on the load and conditions.
My original tyres are wearing well and I would be interested to hear what mileages are being obtained with them.

I'm with you guys on the lower pressures. Guys spend a fortune on suspension upgrades where 26 and 28 Psi fixes all but the biggest issues on the ride. I personally use 1.8 bar (26 Psi) in the front, 2 bar (29 Psi) in the rear unladen, and 2.2 bar (32 Psi) in the rear under laden conditions (my personal guidelines for a Defender 90). I have in over 20 years of Landrover driving (civil Engineering and road building) never torn a sidewall sticking to these pressures. 110 and 130 drivers needs to find an optimum for the rear, but I do not agree with the blanket 40Psi rule (front and rear) that seems to be the standard out here in Northwest Australia.

Rollovers with low pressures would be driver error, especially on rock. When you are crawling (as you should in rock) you often get pretty severe articulation that can result in "bounce". If your tyres are rock hard, the equal/opposite force thing comes into play and a rollover is most likely. Soft tyres (not so soft to break beads and pinch sidewalls) will cusion impact, mould over all but the sharpest rocks and generally give you better grip. A sidewall will damage much easier when rock hard than when it's able to "give" when a rock pushes against it. Obviously unnesesary wheel spin will negate this theory and cut your sidewalls to pieces, hence Low 1st in rock!

This has worked for me over the years and there would be supporters of the other side of the coin.


Cheers!

And you guys find it comfortable to drive at sub 30psi front tyre pressures?
I find at around this the front tyres get very squishy on the road at 110kmph and they wear uneven. Also fuel economy gets worse marginally.
I usually run around 40psi rear and around 38 front.
Not disagreeing, but it may depend on tyres too.

Originally Posted by Loubrey

I'm with you guys on the lower pressures. Guys spend a fortune on suspension upgrades where 26 and 28 Psi fixes all but the biggest issues on the ride. I personally use 1.8 bar (26 Psi) in the front, 2 bar (29 Psi) in the rear unladen, and 2.2 bar (32 Psi) in the rear under laden conditions (my personal guidelines for a Defender 90). I have in over 20 years of Landrover driving (civil Engineering and road building) never torn a sidewall sticking to these pressures. 110 and 130 drivers needs to find an optimum for the rear, but I do not agree with the blanket 40Psi rule (front and rear) that seems to be the standard out here in Northwest Australia.

Rollovers with low pressures would be driver error, especially on rock. When you are crawling (as you should in rock) you often get pretty severe articulation that can result in "bounce". If your tyres are rock hard, the equal/opposite force thing comes into play and a rollover is most likely. Soft tyres (not so soft to break beads and pinch sidewalls) will cusion impact, mould over all but the sharpest rocks and generally give you better grip. A sidewall will damage much easier when rock hard than when it's able to "give" when a rock pushes against it. Obviously unnesesary wheel spin will negate this theory and cut your sidewalls to pieces, hence Low 1st in rock!

This has worked for me over the years and there would be supporters of the other side of the coin.


Cheers!

Lou,

I found "Betty" face a very harsh low profile sport car drive on JLR press guide - so I lowered to your suggested 26F 29R - The ride is far better (nearly comfortable

however my tyre size are R18 - 265/65 any comment on this???

Regards Louis

I think the best thing you can do is try different pressures , ones that suits you ! For example 28psi front and 35psi rear , if most of the time you running empty .You will get to feel what you like , breaking ,wet dry , cornering ect. You can always put a bit more in , or take It out . When I go off road I always let my tyres down , then put them back up once on sealed road . I don't think It is an exact science , different tyres behave different at the same pressure !!.. Jim