Reply With Quotedown the rabbitt hole,,
it sorta looks like a file from file hippo,,
but maybe not--
The MOD Father
the command prompt (as admin) doesnt like devcon- find- *usb* in any order,,
the board has one set of numbers,,
UP215-N101 030827
as for the chip,
the only characters I'm sure of are these
D72010XXXXXXXX
the following ones are illegable,,
I'm fairly certain the board is shown as the NEC USB
but no items show as plugged in... ??
"How long since you've visited The Good Oil?"
'93 V8 Rossi
'97 to '07. sold.
'01 V8 D2
'06 to 10. written off.
'03 4.6 V8 HSE D2a with Tornado ECM
'10 to '21
'16.5 RRS SDV8
'21 to Infinity and Beyond!
1988 Isuzu Bus. V10 15L NA Diesel
Home is where you park it..
[IMG][/IMG]
The MOD Father
down the rabbitt hole,,
it sorta looks like a file from file hippo,,
but maybe not--
"How long since you've visited The Good Oil?"
'93 V8 Rossi
'97 to '07. sold.
'01 V8 D2
'06 to 10. written off.
'03 4.6 V8 HSE D2a with Tornado ECM
'10 to '21
'16.5 RRS SDV8
'21 to Infinity and Beyond!
1988 Isuzu Bus. V10 15L NA Diesel
Home is where you park it..
[IMG]
The MOD Father
lucky me,,
"How long since you've visited The Good Oil?"
'93 V8 Rossi
'97 to '07. sold.
'01 V8 D2
'06 to 10. written off.
'03 4.6 V8 HSE D2a with Tornado ECM
'10 to '21
'16.5 RRS SDV8
'21 to Infinity and Beyond!
1988 Isuzu Bus. V10 15L NA Diesel
Home is where you park it..
[IMG]
Probably not, just checking a few things about pci2.2 your board may not work, its been a while since I used pci slots and stuffed if I can remember what the standards are...
D720101GJ is the NEC controller chip on your usb2.0 pci card...
Here is the data sheet that gives some info for you, in the opening speel.. NEC - datasheet pdf
I'll just have a bit of a read then reply later...
ps, you maybe trying to shove a series1 axle under a disco4...
OK, if you want to see if that card is dead or the wrong settings...
In the BIOS is a setting called "PCI latency", set it to 32 and see if recognises your card... Remember what it was set to before tho cause you may have to set it back...
Also set usb setting in bios to legacy...
If cards not recognised, then can it... All info about drivers etc seem to be win 7 but the same chip comes on a pci-e card and that should be complient with win 10...
To be honest, a new card can be around 20-60 dollars and pci-e, thus usb 3.0 complient...
Anyway, that all can offer...
SysAdmin (Owner)
adding a pci card will usually slow down lots of things that you wouldn't expect it to affect..
pcie overcame many of those difficulties
2007 Discovery 3 SE7 TDV6 2.7
2012 SZ Territory TX 2.7 TDCi
"Make the lie big, make it simple, keep saying it, and eventually they will believe it." -- a warning from Adolf Hitler
"If you don't have a sense of humour, you probably don't have any sense at all!" -- a wise observation by someone else
'If everyone colludes in believing that war is the norm, nobody will recognize the imperative of peace." -- Anne Deveson
“What you leave behind is not what is engraved in stone monuments, but what is woven into the lives of others.” - Pericles
"We can ignore reality, but we cannot ignore the consequences of ignoring reality.” – Ayn Rand
"The happiness of your life depends upon the quality of your thoughts." Marcus Aurelius
| Search AULRO.com ONLY! |
Search All the Web! |
|---|
|
|
|
Bookmarks