Results 1 to 7 of 7

Thread: Broken seat back winder

  1. #1
    Join Date
    Oct 2007
    Location
    Brisbane West
    Posts
    7,373
    Total Downloaded
    0

    Broken seat back winder

    Hi all. o2 model. Tried to wind the seat forward a bit. Felt something snap or strip and no more worky. Ideas? Fixes? Cheers

  2. #2
    Join Date
    Mar 2009
    Location
    Port Stephens N.S.W
    Posts
    3,158
    Total Downloaded
    0
    Uh ... Sounds like it's broken !

    Kev..

    Going ... going ... almost gone ... GONE !! ... 2004 D2a Td5 Auto "Classic Country" Vienna Green

    2014 MUX LST with fruit
    2015 Kimberley Kamper "Classic"

  3. #3
    Join Date
    Apr 2011
    Location
    Melbourne
    Posts
    17
    Total Downloaded
    0

    Seat not moving.

    I recently had the same problem. It could be one of 2 things. Hopefully for you it is just that you blew the 40 amp fuse which goes off with a little crack. This can be found under the passenger seat.
    If the fuse is OK then it is likely to be the motor that drives your seat backwards and forwards that has failed. You can sometimes buy these on eBay (global) I bought an entire set of second hand 4 motors for $120 from the US recently. You will have to remove the seat to replace the motor but it is fairly straighforward. Good Luck .

  4. #4
    Join Date
    Oct 2007
    Location
    Brisbane West
    Posts
    7,373
    Total Downloaded
    0
    Thanks mate. My motor is my hand...its a poverty pack! Generally that things break down less, but this goes against the trend.

    Bump.

    Cheers

  5. #5
    Join Date
    Oct 2007
    Posts
    284
    Total Downloaded
    0

    seat rake knob

    They are a lousy design. The knob is in 2 parts which can be bought individually.It`s usually the inner bit that fits on the shaft that fails.
    That`s the cracking noise you heard.
    the word is that they are becoming hard to find new,so you may have to look around a bit.If you can find one from a wreckers the chances are it will be on the way out anyway.
    My last one I repaired by making an insert with a grub screw to lock it in place on the shaft.

    From memory new ones cost about $35 if you can find one.

    If all else fails carry a small shifting spanner.

    Cheers....Trev.

  6. #6
    Join Date
    Oct 2007
    Location
    Brisbane West
    Posts
    7,373
    Total Downloaded
    0
    Thanks Trev mate. I will strip it down and try grub screwing it. Cheers!

  7. #7
    Join Date
    Oct 2007
    Posts
    284
    Total Downloaded
    0

    broken seat back knob

    What you will probably find is the inner plastic is all cracked away.

    I found an old socket from a set I had which I drilled out and opened up the square drive section by filing it,don`t recall the size,probably 1/4 inch.
    Naturally the seat shaft isn`t a standard size so you need to measure it.

    the socket fitted nicely into the rest of the knob, epoxied into place then drilled and tapped for a grub screw to the shaft .

    Bit of a pain,but I had real hassles sourcing a new one.

    I wanted to keep it standard but if not I probably just would have made a new knob up out of Aluminium.So much easier.

    Trev.

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!