Results 1 to 7 of 7

Thread: New M+S fault as well

  1. 27th October 2012, 04:56 PM #1
    Backtabush's Avatar
    Backtabush
    Backtabush is offline Fossicker
    Join Date
    Oct 2011
    Location
    Gold Coast QLD
    Posts
    59
    Total Downloaded
    0

    New M+S fault as well

    Hi all didn't want to hijack Toppa thread so started a new one I just finished fitting a new d/s/f door actuator and when I started it up to move it I have the M+S lights flashing never had them before stuck the Nanocom on and it gives the fault as.

    (23,4) UNABLE TO DETECT REMOTE CAN NODE, (CURRENT).

    Anyone know what that means surly working on the door didn't do it did it!
    Reply With Quote Reply With Quote
  2. 27th October 2012, 05:11 PM #2
    justinc's Avatar
    justinc
    justinc is offline Swaggie Vendor
    Join Date
    Aug 2006
    Location
    Kingston, Tassie, OZ.
    Posts
    13,728
    Total Downloaded
    0
    Most probably Low battery voltages, try running the engine for 10 minutes or so, then clear the code. Should be fine UNLESS your battery is actually dead/ dying/.

    JC
    Reply With Quote Reply With Quote
  3. 27th October 2012, 05:51 PM #3
    Backtabush's Avatar
    Backtabush
    Backtabush is offline Fossicker
    Join Date
    Oct 2011
    Location
    Gold Coast QLD
    Posts
    59
    Total Downloaded
    0
    Battery only new voltage good but what I remember I had the shifter in reverse when I went to start turned the key nothing WTF I thought and looked around seen it was in reverse stuck it in park and away it went so maybe that's what gave the code I will go out and try it and see if it causes a fault code its good to know.
    Reply With Quote Reply With Quote
  4. 27th October 2012, 05:56 PM #4
    Backtabush's Avatar
    Backtabush
    Backtabush is offline Fossicker
    Join Date
    Oct 2011
    Location
    Gold Coast QLD
    Posts
    59
    Total Downloaded
    0
    Just tried it again but could'nt force a fault code.
    Reply With Quote Reply With Quote
  5. 27th October 2012, 10:13 PM #5
    bsperka
    bsperka is offline Wizard
    Join Date
    Sep 2009
    Location
    Brisbane
    Posts
    1,317
    Total Downloaded
    0

    Changing from R to P is the cause

    Ecu couldn't figure out signal, so went to limp home mode(m&s).
    Reply With Quote Reply With Quote
  6. 27th October 2012, 10:25 PM #6
    OffTrack's Avatar
    OffTrack
    OffTrack is offline YarnMaster
    Join Date
    Feb 2011
    Location
    Brunswick, Victoria
    Posts
    3,778
    Total Downloaded
    0
    The auto and engine ecus communicate via can bus, so the error points to a ccommications failure with the engine ecu.
    Reply With Quote Reply With Quote
  7. 28th October 2012, 05:49 PM #7
    Backtabush's Avatar
    Backtabush
    Backtabush is offline Fossicker
    Join Date
    Oct 2011
    Location
    Gold Coast QLD
    Posts
    59
    Total Downloaded
    0
    Thanks fellows for your inputs sounds about wight no more problems since
    Reply With Quote Reply With Quote
« 04 TD5 running rough | Auto ECU relocation »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!