Results 1 to 6 of 6

Thread: CDL not engaging.

  1. 1st December 2013, 09:00 PM #1
    biggin
    biggin is offline Wizard Subscriber
    Join Date
    Feb 2009
    Location
    Newborough, VIC
    Posts
    1,540
    Total Downloaded
    67.72 MB

    CDL not engaging.

    Went for a spin up around the Thompson Dam this morning. Activated the CDL and noticed the light didn't come on on the dash. It usually takes only a few metres travel for it to come on, but I drove for a couple of hours with no light. At first I thought perhaps the switch was not working properly, but when the rear wheel spun on a difficult section I realised the CDL was not active.
    Given I have solid bar under the chassis to activate the spigot and therefore know for sure that the spigot turned the appropriate amount, what would cause the CDL to not engage.
    I'm hoping I won't have to pull out the transfer case to find out.
    2002 D2 4.6L V8 Auto SLS+2" ACE CDL Truetrac(F) Nanocom(V8 only)
    Reply With Quote Reply With Quote
  2. 2nd December 2013, 08:52 AM #2
    schuy1 Guest
    A- You have torn the guts out of the front diff
    B- you have torn the guts out of the transfer
    C- your front tailshaft has fell off!
    C- A very remote possibility, but maybe a connecting pin in the CDL linkage has fell out
    Cheers Scott
    Reply With Quote Reply With Quote
  3. 2nd December 2013, 09:48 AM #3
    biggin
    biggin is offline Wizard Subscriber
    Join Date
    Feb 2009
    Location
    Newborough, VIC
    Posts
    1,540
    Total Downloaded
    67.72 MB
    If I tore the guts out of anything, I did it very quietly. The feel of the solid linkage is unchanged, so I doubt the linkage is the problem. I will check it though.
    I still have drive from all four wheels at times. It just feels like a normal non-CDL setup. Is it possible for the dog clutch to seize inside the TC?
    2002 D2 4.6L V8 Auto SLS+2" ACE CDL Truetrac(F) Nanocom(V8 only)
    Reply With Quote Reply With Quote
  4. 2nd December 2013, 10:43 AM #4
    schuy1 Guest
    Yeah, with the first 3 theory s it would not have gone quietly The linkage does not have to be out of adjustment very far for it to play up. It is possible for the dog to seize, but unlikely, unless the transfer has had water in over a period of time and the car not driven. Thing is its a very simple system and unless there is lots of noise of the metal kind not much can go wrong.

    Cheers Scott
    Reply With Quote Reply With Quote
  5. 19th January 2014, 06:40 AM #5
    biggin
    biggin is offline Wizard Subscriber
    Join Date
    Feb 2009
    Location
    Newborough, VIC
    Posts
    1,540
    Total Downloaded
    67.72 MB
    Just out of interest, is the CDL engaged indicator lamp on the instrument panel supposed to illuminate during the start-up check?Mine certainly doesn't.
    2002 D2 4.6L V8 Auto SLS+2" ACE CDL Truetrac(F) Nanocom(V8 only)
    Reply With Quote Reply With Quote
  6. 19th January 2014, 09:07 AM #6
    OffTrack's Avatar
    OffTrack
    OffTrack is offline YarnMaster
    Join Date
    Feb 2011
    Location
    Brunswick, Victoria
    Posts
    3,778
    Total Downloaded
    0
    Quote Originally Posted by biggin View Post
    Just out of interest, is the CDL engaged indicator lamp on the instrument panel supposed to illuminate during the start-up check?Mine certainly doesn't.

    No it doesn't. Only when the CDL internals are actually locked
    Reply With Quote Reply With Quote
« Td5 suddenly overheating | white smoke black smoke no power »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!