YarnMaster
Originally Posted by Bohica
Toilet tent?
D4 MY16 TDV6 - Cambo towing magic, Traxide Batteries, X Lifter, GAP ID Tool, Snorkel, Mitch Hitch, Clearview Mirrors, F&R Dashcams, CB
RRC MY95 LSE Vogue Softdash "Bessie" with MY99 TD5 and 4HP24 transplants
SADLY SOLD MY04 D2a TD5 auto and MY10 D4 2.7 both with lots of goodies
ChatterBox
SubscriberThat's it Gavin, also have showers in them as well as being somewhere for "ladies of a certain age" to change.
Governments are just looking for any excuse to shut access to these great places, I'm not about to give them one.
YarnMaster
SubscriberWhy would you need a toilet tent with the sea so close?
D2a Td5 Manual, Chawton White. aka "Daisy"
Build date 11th Oct 2003
Freelander 2 2011, manual, the daughter calls it Perri
Before I had a Land Rover I did not have any torque wrenches. Now I have three.
LROCV #1410
YarnMaster
Why would you need a toilet tent with the sea so close?
Because in WA we try to keep the place pristine for use by others that follow us
D4 MY16 TDV6 - Cambo towing magic, Traxide Batteries, X Lifter, GAP ID Tool, Snorkel, Mitch Hitch, Clearview Mirrors, F&R Dashcams, CB
RRC MY95 LSE Vogue Softdash "Bessie" with MY99 TD5 and 4HP24 transplants
SADLY SOLD MY04 D2a TD5 auto and MY10 D4 2.7 both with lots of goodies
Super Moderator
Because it's not Bondi.Why would you need a toilet tent with the sea so close?
If you don't like trucks, stop buying stuff.
YarnMaster
SubscriberToday I replaced the CV joint. I was unable to remove the hub from the CV joint. So I ordered a new CV joint. Followed the instructions, tapped the shft to seat it in the joint. There did seam to be a lot of splines left over. When I went to fit the hub and all into the axle I had a big gap. Those l;eft over splnes were not left over. I hit the shaft with a hammer to seat it. No movement until the 5th hit, when the CV joint dropped about the same length as the left over splines. More fun and games with the 32mm nut, the 490Nm nut, except the one that came with the CV joint was 35.86m, ok 36mm. The same for the nut that came with the hub. When did the size change? I had a spare 32mm nut and used that. I don't mind the size, but when you only have a 32mm socket, it is annoying.
There was the usual fun and games putting the caliper back on, I had a problem with the ABS plug, I could not push it fully home. I removed the catch can hoses to get a better grip, and noticed a slight collar on the plug. I was seating this correctly, I just didn't realise it.
I cleared the 4 amigos faults and went for a test drive, upto 100kph on the road to Geelong. I am it seems friendless, I couldn't be happier. I gave the car a wash, washed the seat covers and the floor mats. Now I need a nap. After 6 months the car is good to go.
D2a Td5 Manual, Chawton White. aka "Daisy"
Build date 11th Oct 2003
Freelander 2 2011, manual, the daughter calls it Perri
Before I had a Land Rover I did not have any torque wrenches. Now I have three.
LROCV #1410
Super Moderator
Go where? I'm sure you'd find some friends in Queensland.
If you don't like trucks, stop buying stuff.
TopicToaster
SupporterGood to go searching for a D4 I think ....
Arthur.
All these discos are giving me a heart attack!
'99 D1 300Tdi Auto ( now sold :( )
'03 D2 Td5 Auto
'03 D2a Td5 Auto
Master
Used the first few days of holidays to get some maintenance done, replaced the injector seals and loom, also changed diff oils and transfer case oil. While I have the rocker cover off, I gave a quick sand blast and a coat of high temp paint.
Just need to finish fitting some new seat covers I bought a while ago, then it's ready for some holiday trips.
Cheers Discofender20241219_210835.jpg20241220_160149.jpg20241216_185641.jpg
Super Moderator
That would take a braver man than me.Good to go searching for a D4 I think ....
If you don't like trucks, stop buying stuff.
Posting Permissions
| Search AULRO.com ONLY! |
Search All the Web! |
|---|
|
|
|
Reply With Quote
Bookmarks