Thread: No acceleration, engine dies.......

Originally Posted by Nomad9

Hi Sierrafery,
I've just been and checked again, much as it pains me , you are right, the manifold pressure I am seeing is actually the inlet manifold pressure I now believe, not the fuel manifold pressure, however I am still only hearing one pump kick in. I'm still hedging my bets on the fuel pump.

Cheers Marty

To rule out the pump without swapping it with known good one you need a hydraulic pressure gauge with an adaptor as to be able to screw it instead of the FT sensor in the FPR.... then you can see if you get 4 bar there or not

Hi Ean,
Like the way you think, I have checked the fuel lines now against my stepsons D2, they look to be the same, plus I'm not sure that I would be able to get it to run, I did do around 15 to 20 klms after the head rebuild, I'm sort of ruling this out unless someone can advise me differently.

Cheers Marty

Hi Rob,
I don't think the head I installed had one, I certainly didn't fit one. A few of the heads I have done the fine mesh has already been left out by previous head removalists.

Thanks for the suggestion.

Cheers Marty

Originally Posted by Nomad9

Hi Ean,
Like the way you think, I have checked the fuel lines now against my stepsons D2, they look to be the same, plus I'm not sure that I would be able to get it to run, I did do around 15 to 20 klms after the head rebuild, I'm sort of ruling this out unless someone can advise me differently.

Cheers Marty

Yeh I did wonder about the 15 - 20 ks drive myself , but if it makes someone think outside the box it may make them think of something that so far hasn't been mentioned.


I was more thinking if the fuel return was blocked or wrong it may effect the fuel pressure and that could be the cause.


As I said its out of left field but worth a mention.


Cheers Ean

Hi There,
Things checked today:-

Fuel filter replaced(again) system bled

Checked the routing of the fuel lines they appear to be ok

Took the MAF sensor of my Stepsons D2, nothing different

Found a pipe off a small solenoid connected to the " after turbo pipe" and a connection to the wastegate diaphragm + an electrical connection, replaced no difference.

Cleaned all the electrical connectors I disturbed during the head repacement except the one on the fuel pressure regulator. Just a bit to difficult to get to

Cleaned the MAP sensor in the inlet mainifold.

Checked there is nothing loose connection wise on the accelerator pedal, I didn't manage to get the wires off, just checked that they were on and tight.

So now I'm at a loss. The state of play now, the engine will start every time, on some occasions I can press the "go pedal" and the engine will rev something like normal but doesn't have much power. If the engine stalls whilst I am moving the vehicle, the engine will start and idle however the engine won't rev. If I now press the go pedal maybe four or five times in succession the yellow engine light starts to flash, no increase in engine revs. I can turn the engine off, turn it back on again no engine light flashing.

When I chnaged the fuel filter the fuel pump seemed to make its usual bleeding noises and then settled down to a steady hum.

Got me a bit stumped this one. Still no DTC's active at all.

Cheers Marty

RAVE shows the low side of the pump keeps the fuel filter primed and the high side feeds fuel to the FPR then the injectors.

I am wondering if the low side is supplying enough fuel for the car to idle but if the high side isn't pumping then it won't supply enough fuel to rev the engine.

It could be a case of the high side failed after your short drive . Fitting a different pump will tell but I guess you need to see if someone has 1 you can try.

The fuel then goes from the injectors, to the FPR , the fuel cooler , filter then tank so unless a fuel line in kinked or blocked between the injectors and the filter it can't be much else.

Just my view anyway

Cheers Ean

Hi Ean,
I have checked all I really can now without actually replacing some parts, my prime candidates are the throttle position sensor and the fuel pump. I'll have a chat with the guys at TRS tomorrow morning they will know what the problem is and they will have the parts.

As I have heard on so many occasions "it will be something simple" if its that simple why can't I find it that easily. Sierrafery has aligned with your thoughts, I'm also pretty well sold on the fuel pump. However some of the symptoms I have read about point me to the TPS, I'm not sure how often or common a failing point they are.

Your opinions are always valued, thank you.

Cheers Marty

Hi Marty
A couple of things to check seeing you've done recent work, make sure you did the injector lock nuts up when you checked bump clearances, and while the rocker cover is off , double check your cam timing ,and sprocket bolt tension, for what its worth , I reckon you will have a mesh filter in the head but it's hidden behind a fat o ring behind the fpr. Also I have seen what Ean was talking about re fuel lines around the wrong way and the blokes car ran fine for about 50 kilometers after he did the head .