Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: Llams install Perth

  1. 21st March 2020, 06:22 PM #11
    Simeon Prucha
    Simeon Prucha is offline Member
    Join Date
    Feb 2020
    Location
    ACT, Australia
    Posts
    3
    Total Downloaded
    0

    LLAMS kit instructions download issues..?

    Quote Originally Posted by ~Rich~ View Post
    Easy as long as you are a bit of a contorsionist!

    Loom: Box

    Switch: Box

    I can't seem to access / download the installation instructions. Just bought the kit and wanting to fit it to my 2015 LR4
    Reply With Quote Reply With Quote
  2. 21st March 2020, 06:48 PM #12
    Mog60's Avatar
    Mog60
    Mog60 is offline Master Supporter
    Join Date
    May 2015
    Location
    Perth
    Posts
    133
    Total Downloaded
    0
    Quote Originally Posted by Simeon Prucha View Post
    I can't seem to access / download the installation instructions. Just bought the kit and wanting to fit it to my 2015 LR4
    Hope this helps,
    Attached Files Attached Files
    2014 D4 HSE, Traxide Dual Battery System, llams, Compomotive Rims, Prospeed Roof Rack, Rock Sliders and Compressor Guard.
    Reply With Quote Reply With Quote
  3. 10th April 2020, 03:01 PM #13
    Simeon Prucha
    Simeon Prucha is offline Member
    Join Date
    Feb 2020
    Location
    ACT, Australia
    Posts
    3
    Total Downloaded
    0
    Than ks Mog60. I fitted it today to my LR4. Relatively easy but now getting suspension faults... :-(
    Reply With Quote Reply With Quote
  4. 10th April 2020, 05:04 PM #14
    Mog60's Avatar
    Mog60
    Mog60 is offline Master Supporter
    Join Date
    May 2015
    Location
    Perth
    Posts
    133
    Total Downloaded
    0
    Did you disconnect the battery before fitting? If not you might expect to see some faults occur. From memory some have said these will go after cycling the ignition a few times.

    The following comes from the instructions:-

    Reconnect the battery and switch on the ignition. A suspension fault may be shown if the battery was not disconnected,
    in which case switch the ignition off then on to clear the message. If a fault message is still displayed then refit all
    connectors.

    Hope it sorts itself.







    .
    2014 D4 HSE, Traxide Dual Battery System, llams, Compomotive Rims, Prospeed Roof Rack, Rock Sliders and Compressor Guard.
    Reply With Quote Reply With Quote
  5. 10th April 2020, 06:39 PM #15
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,030
    Total Downloaded
    0
    I've been in contact with Simeon regarding the faults. Something is amiss.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  6. 27th April 2020, 06:33 PM #16
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,030
    Total Downloaded
    0
    One of the ICs in the LLAMS module was faulty in a manner that I've not seen before which wasn't spotted during module checking even though it would have been showing on the oscilloscope.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
Page 2 of 2 FirstFirst 12
« Changes to the D3 | Falken Wildpeak AT3W »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!