Results 1 to 7 of 7

Thread: Xenon Lights for TDV6

  1. 19th January 2014, 04:45 PM #1
    giskard
    giskard is offline Master Supporter
    Join Date
    Sep 2013
    Location
    Australia
    Posts
    100
    Total Downloaded
    0

    Xenon Lights for TDV6

    I have an MY13 TDV6 that has the standard halogen lights. After a little research, it sounds like its possible to get Xenons and then get them enabled via a service menu of some sort?

    Has anyone done this? If so, what sort of money are you looking at to get this done?

    Thanks in advance.
    Reply With Quote Reply With Quote
  2. 19th January 2014, 05:20 PM #2
    Sparkybreno's Avatar
    Sparkybreno
    Sparkybreno is offline Fossicker
    Join Date
    Oct 2013
    Location
    Brisbane
    Posts
    21
    Total Downloaded
    0
    I'm interested in this as well. Just took delivery two days ago of an my13 tdv6 with a stack of options but not xenons. Coming from a car with bi-xenon lights it will be difficult to adjust. I notice it has separate low and high beam lamps so a bi-xenon setup may be possible?
    Reply With Quote Reply With Quote
  3. 19th January 2014, 07:36 PM #3
    Graeme
    Graeme is offline Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,033
    Total Downloaded
    0
    The whole assembly needs to be replaced. Expensive new but perhaps used ones can be obtained from the UK.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  4. 19th January 2014, 07:43 PM #4
    ytt105
    ytt105 is offline Master Supporter
    Join Date
    Jan 1970
    Location
    NSW Far South Coast
    Posts
    685
    Total Downloaded
    0
    What about the aftermarket kits?

    Has anyone installed them?
    Reply With Quote Reply With Quote
  5. 19th January 2014, 07:49 PM #5
    sheerluck Guest
    There's a couple of places selling the OEM assembly, for about £350. But the shipping cost is a killer.
    Reply With Quote Reply With Quote
  6. 19th January 2014, 10:47 PM #6
    RichardK
    RichardK is offline ChatterBox Silver Subscriber
    Join Date
    Jan 1970
    Location
    Western Australia
    Posts
    2,955
    Total Downloaded
    0
    I bought brand new assemblies out of UK (50% cheaper than LRA stealers). They are plug and play, just remove the QH assemblies and install, they work without doing anything to the ECU's although I did change my instrument pack's system configuration later to BX
    RichardK

    Series IV Matrix Offroad Camper following our Discovery 3 with E Diff, BAS Remap, Mitch Hitch, Uniden UHF, Codan NGT HF, Masten TPMS, Proquip Compressor Guard, ARB Winch Bar, Milemarker Hydraulic Winch, 4x4 Intelligence Rear Wheel Carrier, VMS GPS with Rear Camera,
    Reply With Quote Reply With Quote
  7. 20th January 2014, 02:42 PM #7
    discojools's Avatar
    discojools
    discojools is offline Master Subscriber
    Join Date
    Nov 2009
    Location
    Mornington Peninsula
    Posts
    707
    Total Downloaded
    0
    Quote Originally Posted by RichardK View Post
    I bought brand new assemblies out of UK (50% cheaper than LRA stealers). They are plug and play, just remove the QH assemblies and install, they work without doing anything to the ECU's although I did change my instrument pack's system configuration later to BX
    Where did I you get them from and how much delivered ? Of course if went ahead I might have to take off my OL bar! Haven't had to change a bulb yet on my D4 TDV6 so don't know about removing light assembly. I know I couldn't on my previous ARB barred D3.
    Reply With Quote Reply With Quote
« A pillar trim removal | D3 Suspension Bushes »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!