Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: MAP problem D3

  1. 9th April 2016, 09:53 AM #1
    Tinman
    Tinman is offline Master
    Join Date
    Jan 1970
    Posts
    229
    Total Downloaded
    0

    MAP problem D3

    Hi Guys, After seeing a thread just recently I decided to give my MAP sensor a clean. When I removed it from the electronic throttle body it was completely blocked. The hole it came out of was full of gunk so used a vacuum cleaner while I scratched away the gunk. Next came the sensor which cleaned up quite well my09 sensor has a 6mm hole so a lot bigger hole than in the earlier ones. I fitted the cleaned sensor and started the vehicle. A whole series of faults showed up including turbo transmission with a F in the instrument display connected the Nanocom cleared the faults but they wont go away. Unable to drive the vehicle as it has limited gears available. Seems to be a problem with the MAP sensor. Phoned up to get one from a dealership hope you are sitting down $720.00 . Does anyone know where I can get one a bit cheaper. The Boss is not very happy at the moment.
    Reply With Quote Reply With Quote
  2. 9th April 2016, 01:16 PM #2
    AnD3rew's Avatar
    AnD3rew
    AnD3rew is offline Wizard
    Join Date
    Jun 2009
    Location
    Sydney
    Posts
    1,563
    Total Downloaded
    0
    They are about ?63 plus S&H from Rimmer in the UK but it will take a little while to get here.
    Reply With Quote Reply With Quote
  3. 9th April 2016, 01:38 PM #3
    Tinman
    Tinman is offline Master
    Join Date
    Jan 1970
    Posts
    229
    Total Downloaded
    0
    Thanks Andrew will get on to that. $720 bloody outrageous
    Many thanks again
    Reply With Quote Reply With Quote
  4. 9th April 2016, 02:33 PM #4
    Fatso's Avatar
    Fatso
    Fatso is offline Wizard
    Join Date
    Mar 2012
    Location
    Gabbadah WA
    Posts
    1,438
    Total Downloaded
    0
    Surely the person who quoted that price must on drugs , or has made a big mistake in looking up the part .
    Reply With Quote Reply With Quote
  5. 9th April 2016, 03:07 PM #5
    Tinman
    Tinman is offline Master
    Join Date
    Jan 1970
    Posts
    229
    Total Downloaded
    0
    I rang the guy twice at Macarthur landrover as I thought he had made a mistake with which part I wanted but came back with the same result he told me to check ebay and other avenues as he told me it was over the top. Rimmer in UK $121Aud for genuine Land Rover we must have excessive taxes for it to be $720 in Australia
    Reply With Quote Reply With Quote
  6. 9th April 2016, 03:45 PM #6
    Graeme
    Graeme is online now Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,030
    Total Downloaded
    0
    A few years ago I got one from the UK in about 4 days for my 3.0 (same as later 2.7) to get it faster than going through the warranty exercise, which I eventually did but without the inconvenience.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  7. 9th April 2016, 03:46 PM #7
    LRD414's Avatar
    LRD414
    LRD414 is offline Super Moderator Subscriber
    Join Date
    Oct 2014
    Location
    Brisbane
    Posts
    3,737
    Total Downloaded
    0

    MAP problem D3

    Or he quoted including the housing assembly it sits in perhaps? Check with roverlord as well (vendor on here). Mario got me a couple of spare sensors recently for good value.

    Scott
    D4 TDV6 MY14 with Llams, Tuffant Wheels, Traxide DBS, APT sliders & protection plates, Prospeed Winch Mount w/ Carbon 12K, Mitch Hitch & Drifta Drawers
    Link to my D4 Build Thread
    D3 2005 V8 Petrol
    Ex '77 RRC 2 door. Long gone but not forgotten.
    Reply With Quote Reply With Quote
  8. 9th April 2016, 04:07 PM #8
    Tinman
    Tinman is offline Master
    Join Date
    Jan 1970
    Posts
    229
    Total Downloaded
    0
    Price was only for the sensor. My MAP sensor has nearly a 6 mm opening where all the others have a nipple with a small opening are all the D3 map sensors the same. I Have a LR part no from Rimmer in the Uk will have to check if its the same for my09 on Monday from the Dealers before or give Mario a ring. Thanks heaps guys for your feedback
    Reply With Quote Reply With Quote
  9. 11th April 2016, 04:27 PM #9
    Tinman
    Tinman is offline Master
    Join Date
    Jan 1970
    Posts
    229
    Total Downloaded
    0

    Smile

    New map sensor fitted car back to normal cleared all the logged faults and took for a test drive then checked for faults none to be found yippee the boss will be happy.
    Reply With Quote Reply With Quote
  10. 11th April 2016, 05:20 PM #10
    LRD414's Avatar
    LRD414
    LRD414 is offline Super Moderator Subscriber
    Join Date
    Oct 2014
    Location
    Brisbane
    Posts
    3,737
    Total Downloaded
    0
    Good result. Where'd you get it in the end and how much?

    Scott
    D4 TDV6 MY14 with Llams, Tuffant Wheels, Traxide DBS, APT sliders & protection plates, Prospeed Winch Mount w/ Carbon 12K, Mitch Hitch & Drifta Drawers
    Link to my D4 Build Thread
    D3 2005 V8 Petrol
    Ex '77 RRC 2 door. Long gone but not forgotten.
    Reply With Quote Reply With Quote
Page 1 of 2 12 LastLast
« What do these buttons do??? | New Territory engine in D3, Engine System Fault, please help »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!