Results 1 to 8 of 8

Thread: Overhaul Alternator ?

  1. 27th November 2016, 10:30 AM #1
    Ean Austral Guest

    Overhaul Alternator ?

    Gday All,

    Has anyone overhauled a alternator ? From what I have heard the parts are not available but that seems odd,

    I have a spare alternator that I removed at around 130k and it was still working fine. From what I have read they are prone to failure from about 140k so just wondering if it's a worthwhile exercise.

    Cheers Ean
    Reply With Quote Reply With Quote
  2. 27th November 2016, 11:39 AM #2
    Graeme
    Graeme is online now Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,030
    Total Downloaded
    0
    The diodes usually fail before any other component and diode packs are available. However it's not worthwhile replacing the diode pack without replacing the bearings, skimming the slip rings and fitting a new regulator yet the insulation on the wires will have degraded from heat and age. I suggest keeping it as a spare for emergency fitting.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  3. 27th November 2016, 12:20 PM #3
    Ean Austral Guest
    Quote Originally Posted by Graeme View Post
    The diodes usually fail before any other component and diode packs are available. However it's not worthwhile replacing the diode pack without replacing the bearings, skimming the slip rings and fitting a new regulator yet the insulation on the wires will have degraded from heat and age. I suggest keeping it as a spare for emergency fitting.
    Thanks Graeme, making sure you put the plug in the back the correct way is a good start when it's fitted. . Thought I should get in first before any one else

    With the cost of new it's basically an economic write off when it needs to be overhauled.

    Cheers Ean
    Reply With Quote Reply With Quote
  4. 27th November 2016, 12:46 PM #4
    Graeme
    Graeme is online now Swaggie Vendor
    Join Date
    Jan 1970
    Location
    NSW SW Slopes
    Posts
    12,030
    Total Downloaded
    0
    A family member is the local rep for a significant automotive electrical component manufacturer (not Denso) as suppliers to vehicle manufacturers and to the after-market trade. They do not supply rebuild parts for their alternators because by the time one component fails, the others wont be far behind.
    MY21.5 L405 D350 Vogue SE with 19s. Produce LLAMS for LR/RR, Jeep GC/Dodge Ram
    VK2HFG and APRS W1 digi, RTK base station using LoRa
    Reply With Quote Reply With Quote
  5. 27th November 2016, 01:55 PM #5
    LandyAndy's Avatar
    LandyAndy
    LandyAndy is offline RoverLord Gold Subscriber
    Join Date
    Feb 2004
    Location
    Williams West Aust
    Posts
    20,998
    Total Downloaded
    0
    Is there any chance that reversing that plug has fried the diodes????
    Worth getting it bench tested???,what a pain to go thru the hassle of fitting it and finding its toast.
    Andrew
    DISCOVERY IS TO BE DISOWNED
    Midlife Crisis.Im going to get stuck into mine early and ENJOY it.
    Snow White MY14 TDV6 D4
    Alotta Fagina MY14 CAT 12M Motor Grader
    2003 Stacer 525 Sea Master Sport
    I made the 1 millionth AULRO post
    Reply With Quote Reply With Quote
  6. 27th November 2016, 02:30 PM #6
    Ean Austral Guest
    Quote Originally Posted by LandyAndy View Post
    Is there any chance that reversing that plug has fried the diodes????
    Worth getting it bench tested???,what a pain to go thru the hassle of fitting it and finding its toast.
    Andrew
    I am going to test it , don't think it ran long enough but plan to find out before its needed .
    I was more looking at the viability of a full service but if your not in a rush I think they can be purchased for about $400 . It don't take much to make it uneconomic at $100/hr for a auto sparkie.
    Reply With Quote Reply With Quote
  7. 27th November 2016, 09:45 PM #7
    PAT303
    PAT303 is offline OldBushie
    Join Date
    May 2007
    Location
    Safety Bay
    Posts
    8,041
    Total Downloaded
    0
    Replacing the diodes has been the norm for years in Land Loosers,they last many a mile if it's done every 100k or so. Pat
    Reply With Quote Reply With Quote
  8. 28th November 2016, 01:28 PM #8
    vee8auto
    vee8auto is offline Master
    Join Date
    Jan 2010
    Location
    Bunbury WA
    Posts
    125
    Total Downloaded
    0
    I got the diode bridge / assembly from an eBay seller in Ireland, delivered to Australia for a reasonable cost. The diodes in mine were fried at around 190,000 ks, they went at the same time as the air compressor and the battery, so I suspect some sort of collusion there..

    Otherwise, I used to rebuild & rewind electrical motors and alternators and stuff in a previous life. So in my opinion the stator and rotor are very well built, and the winding enamel was perfectly serviceable. The slipring looked good for a spare, but new brushes needed.

    The only problem I ran into was how to get the clutched pulley off ?? to change the drive end bearing. I didnt want to destroy it so it now sits as one of those projects awaiting more info and a roundtuit.
    Reply With Quote Reply With Quote
« Hissing Noise | Fitting a bigger auxiliary battery »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!