Results 1 to 6 of 6

Thread: Charging a dead flat battery

  1. 16th June 2021, 09:18 AM #1
    BradC
    BradC is offline Super Moderator
    No one of consequence     Supporter
    Join Date
    Mar 2018
    Location
    Perth (near Malaga)
    Posts
    3,545
    Total Downloaded
    0

    Charging a dead flat battery

    This is just a thought triggered by the "charge through the 12S socket" thread.

    A month or so ago I left the iiDtool engaged on the D3 and ran the battery flat. Completely flat (<8V).

    I usually charge with a CC/CV bench power supply (0-30V 0-10A). I put the power supply on the battery and it shot up to about 9V at which time the car started to boot, drew much more than 10A and pulled the battery down below 8V where it all stopped. The car was stuck in this loop where it was trying to boot but 10A wasn't enough. I ended up disconnecting the battery to put a good surface charge on it before hooking it back up to allow the car to boot.

    Once the computers booted up, the current consumption dropped below 10A and the battery continued to charge.

    I've heard of people powering the car up through the 12S socket enough to get the doors unlocked, but even with 10A I was unable to get enough into it to allow the BCM to fully boot. It wouldn't respond to the remote.

    Has anyone managed to charge a car from dead without disconnecting the battery? A jump start would be fine, as I assume would be a battery charger with > 10A capability.
    Reply With Quote Reply With Quote
  2. 16th June 2021, 09:34 AM #2
    BMKal's Avatar
    BMKal
    BMKal is online now ForumSage Gold Subscriber
    Join Date
    Mar 2007
    Location
    Kalgoorlie WA
    Posts
    5,546
    Total Downloaded
    0
    I got home last week from 5 months working interstate, and mine was down to 5V.
    I used the key to open the passenger's door and bonnet. When I first put a CTek charger on the battery while it was connected, it seemed to be taking charge OK, but strange things were happening like tail lights were continually flashing etc. So I disconnected the battery and left it on charge overnight - it came back up to almost 13V.

    When I re-connected the next morning, the car alarm went off (as it should have because I had used the key to open the door). I cancelled this by pressing the button the key fob, started the engine and re-set the dash clock and "auto-up" on the windows, and haven't had a problem since. I have dual voltage meters mounted on the console (for cranking and aux batteries). Both batteries are running at normal voltage since charging.
    Reply With Quote Reply With Quote
  3. 16th June 2021, 09:45 AM #3
    BradC
    BradC is offline Super Moderator
    No one of consequence     Supporter
    Join Date
    Mar 2018
    Location
    Perth (near Malaga)
    Posts
    3,545
    Total Downloaded
    0
    Quote Originally Posted by BMKal View Post
    Istrange things were happening like tail lights were continually flashing etc. So I disconnected the battery and left it on charge overnight - it came back up to almost 13V.
    Yeah, that was my thing. I could also hear what sounded like the turbo actuator and EGR valves cycling.
    Reply With Quote Reply With Quote
  4. 18th June 2021, 03:45 PM #4
    loanrangie's Avatar
    loanrangie
    loanrangie is offline LordRover Subscriber
    Join Date
    Jan 1970
    Location
    St Helena,Melbourne
    Posts
    16,770
    Total Downloaded
    1.13 MB
    Usually if a battery is that dead you'd need it to connect to another good battery like you were jumping it so as to bring the voltage up so that a charger can detect it and commence charging.
    MY08 TDV6 SE D3- permagrin ooh yeah
    2004 Jayco Freedom tin tent
    1998 Triumph Daytona T595
    1974 VW Kombi bus
    1958 Holden FC special sedan
    Reply With Quote Reply With Quote
  5. 18th June 2021, 04:55 PM #5
    Hogarthde
    Hogarthde is offline Master
    Join Date
    Aug 2012
    Location
    Encounter Bay
    Posts
    926
    Total Downloaded
    0
    Yep, that’s what I did on the farm years ago.
    Although I don’t know if my newish charger needs the same reminder, I am with Nick...connect two , one good, one flat for a while
    Reply With Quote Reply With Quote
  6. 18th June 2021, 05:53 PM #6
    drivesafe's Avatar
    drivesafe
    drivesafe is offline OldBushie Vendor
    Join Date
    Jan 1970
    Location
    Queensland
    Posts
    7,904
    Total Downloaded
    0
    It also depends on the type of battery charger.

    Many chargers have a Power Supply Mode, and if you have a battery that is so low that the charge will not charge it, switch to Power Supply Mode and charge the battery in this mode for a while.

    Then switch back to the normal battery charging mode, job done.

    NOTE, you may need to charge the battery in Power Supply mode for a few hours, before the charger mode will work.

    This is actually something that is require more now with lithium batteries that have been discharged low enough that their BMS has shut down the battery.

    Most chargers will not charge them, so you switch to the Power Supply Mode. Run it on the lithium battery for a few SECONDS and then you can use the charger mode.

    So something to consider when choosing that new battery charger. Future-proof your uses and make sure it has a Power Supply Mode.

    For Land Rover Specific Dual Battery Systems and Headlight Wiring Upgrade Kits,
    Reply With Quote Reply With Quote
« Timing belt change after 7yrs and 37,000kms | Connecting light bar to D4 with Bi Xenon »

Tags for this Thread

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!