Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 34

Thread: Air suspension woes ....

  1. #21
    Join Date
    Dec 2009
    Location
    Tyrendarra Vic (South West Vic )
    Posts
    1,729
    Total Downloaded
    0
    That explains the price.

  2. #22
    Join Date
    Dec 2009
    Location
    Tyrendarra Vic (South West Vic )
    Posts
    1,729
    Total Downloaded
    0
    Not quite sure what you meen . But here goes

    Lower front arm is VIN dependant
    Bush is : RBX00070

    Upper front arm RH kit : RBJ000120 Ball joint to suit is VIN dependant
    LH kit : RBJ000130 Ball joint to suit is VIN dependant
    Bush is : RBX000200

    All bush bolts are M14 x 103 mm . Nuts are M14

    If you need more will require your VIN

    Hope this helps

    Gary

  3. #23
    Join Date
    May 2012
    Location
    australia brisbane
    Posts
    85
    Total Downloaded
    0
    Ok so I found a picture of the one I need (the lower in the pic) ... as described above Front passenger wheel lower arm ( the one closer to the back of the wheel arch)
    Is this the one I need the vin for ?
    Attached Images Attached Images

  4. #24
    Join Date
    Dec 2009
    Location
    Tyrendarra Vic (South West Vic )
    Posts
    1,729
    Total Downloaded
    0
    Looking on Microcat the arm at the bottom of picture is the upper arm ( longer arm )

    Upper front arm RH kit : RBJ000120 Ball joint to suit is VIN dependant
    LH kit : RBJ000130 Ball joint to suit is VIN dependant
    Bush is : RBX000200

  5. #25
    Join Date
    Dec 2009
    Location
    Tyrendarra Vic (South West Vic )
    Posts
    1,729
    Total Downloaded
    0
    If your arm is O'k then just replace bush & ball joint. 3 different ball joints between 2002 -2009.

    Gary

  6. #26
    Join Date
    May 2012
    Location
    australia brisbane
    Posts
    85
    Total Downloaded
    0
    do the bushes require being pressed in with a workshop press or are they just a push fit ?

  7. #27
    Join Date
    Dec 2009
    Location
    Tyrendarra Vic (South West Vic )
    Posts
    1,729
    Total Downloaded
    0
    Quote Originally Posted by philmoon View Post
    do the bushes require being pressed in with a workshop press or are they just a push fit ?
    Don't know. Sorry Phil

    Gary

  8. #28
    Join Date
    Dec 2009
    Location
    Tyrendarra Vic (South West Vic )
    Posts
    1,729
    Total Downloaded
    0
    Just had a look at RAVE. There is a special LR tool for removing & installing bushes. But you could do the same with a couple of sockets & a long bolt. Should be fitted in pairs.

    Gary

  9. #29
    Join Date
    Mar 2012
    Location
    Launceston, Tas
    Posts
    9
    Total Downloaded
    0
    Just had these replaced on mine. They needed a 30 ton press ( to get the old ones out) and needed to make an special tool to help push the bush in as the metal around the rubber bush is soft, the bushes also require alignment to the arm, if you haven't done this work before I'd suggest a good Indy to it! I took my lower control arms off the vehicle, dropped them in to the Indy garage for them to press them in.. If you do it this way good luck with the ball joints, one of mine was a real ### to get out..

  10. #30
    Join Date
    May 2012
    Location
    australia brisbane
    Posts
    85
    Total Downloaded
    0
    I will just buy new ones then lol thats too much effort they are only 80 each

Page 3 of 4 FirstFirst 1234 LastLast

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!