Results 1 to 7 of 7

Thread: Series Overdrive - measurement please?

  1. 10th June 2011, 01:44 PM #1
    Lotz-A-Landies's Avatar
    Lotz-A-Landies
    Lotz-A-Landies is offline Super Moderator Gold Subscriber
    Join Date
    Jul 2006
    Location
    East-South-East Girt-By-Sea
    Posts
    17,662
    Total Downloaded
    1.20 MB

    Series Overdrive - measurement please?

    Does anyone have a series overdrive out of the vehicle ATM?

    Doesn't matter which brand.

    Can someone measure the inside diameter of the bore in the output shaft.

    Diana

    You won't find me on: faceplant; Scipe; Infragam; LumpedIn; ShapCnat or Twitting. I'm just not that interesting.
    Reply With Quote Reply With Quote
  2. 10th June 2011, 03:33 PM #2
    123rover50's Avatar
    123rover50
    123rover50 is offline YarnMaster Supporter
    Join Date
    Jun 2009
    Location
    Queensland
    Posts
    3,434
    Total Downloaded
    0
    Do you mean the big hole in the front or the little bush down inside?
    Reply With Quote Reply With Quote
  3. 10th June 2011, 08:29 PM #3
    Lotz-A-Landies's Avatar
    Lotz-A-Landies
    Lotz-A-Landies is offline Super Moderator Gold Subscriber
    Join Date
    Jul 2006
    Location
    East-South-East Girt-By-Sea
    Posts
    17,662
    Total Downloaded
    1.20 MB
    I mean the big hole at the front end, the one that the clutch sleeve and bearing runs inside.

    You won't find me on: faceplant; Scipe; Infragam; LumpedIn; ShapCnat or Twitting. I'm just not that interesting.
    Reply With Quote Reply With Quote
  4. 10th June 2011, 08:38 PM #4
    series3's Avatar
    series3
    series3 is offline Master
    Join Date
    Jun 2008
    Location
    Morpeth NSW
    Posts
    782
    Total Downloaded
    0
    Hi,

    I have a toro at home that I can check.. Will let you know.

    Sam
    Reply With Quote Reply With Quote
  5. 11th June 2011, 05:41 AM #5
    123rover50's Avatar
    123rover50
    123rover50 is offline YarnMaster Supporter
    Join Date
    Jun 2009
    Location
    Queensland
    Posts
    3,434
    Total Downloaded
    0
    Best I can get is 2.280"
    Reply With Quote Reply With Quote
  6. 11th June 2011, 12:50 PM #6
    Johnno1969's Avatar
    Johnno1969
    Johnno1969 is offline Wizard Supporter
    Join Date
    Dec 2009
    Location
    Queensland (though occasionally elsewhere)
    Posts
    1,431
    Total Downloaded
    0
    My callipers are getting a bit old, but I get 57.5mm.

    Hope that helps.

    John
    Reply With Quote Reply With Quote
  7. 11th June 2011, 08:20 PM #7
    Lotz-A-Landies's Avatar
    Lotz-A-Landies
    Lotz-A-Landies is offline Super Moderator Gold Subscriber
    Join Date
    Jul 2006
    Location
    East-South-East Girt-By-Sea
    Posts
    17,662
    Total Downloaded
    1.20 MB
    Thanks mates!

    2.280" is 57.9mm by my conversion. so the measurement adequate for current needs.

    The reason, is for my SIIB Overdrive project. I purchased a NOS mainshaft gear for the all helical F/C & one ton box, and was concerned there wouldn't be sufficient meat to hold the teeth of the gear.

    If the bore is less than 58mm and the space between the teeth 71mm dia, I will still have at least 6.5mm. Would like more but at least is is not less, now to discuss with the engineering company.

    You won't find me on: faceplant; Scipe; Infragam; LumpedIn; ShapCnat or Twitting. I'm just not that interesting.
    Reply With Quote Reply With Quote
« Series IIa on SeriesIII Chassis | Can you ID this one? »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!