Disco headlining

**p38arover** · 27th February 2011, 05:25 PM

I might have half a can, too.

**PhilipA** · 27th February 2011, 08:52 PM

I have some lovely coloured pins left over from repinning the Camry wagon that I bought on behalf of my daughter.

Regards Philip A

**harry** · 27th February 2011, 08:58 PM

currumbin trimming can fix it
not expensive, and done in a day.

give them a ring, tell them harry sent you,
and all that will be no use to you if you aren't near here.

so post your location in your details so someone in your area can assist you.

come up here and call drew, he's good.

**dolphint** · 27th February 2011, 09:34 PM

Originally Posted by Mr Whippy

I can also add half a can. I had a quote of $150 if I removed it. If you have it removed why would you bother trying to glue it when it can be done properly for 150 bucks?

Dave.

Dave, were did you get the quote foe $150 bucks? I'd jump at that, it would even be worth a few hours drive for that.

**d2dave** · 27th February 2011, 11:57 PM

It was a motor trimmer in Shepparton. If you want next time I am in Shepp I can go and double check that price if you want,

Dave.

Hamish71 · 28th February 2011, 11:23 AM

I swear, my PM box is full of requests for this info. Im in Melbourne I went here to this place in Oakleigh:

Auto Sunroof and Trimming Melbourne

Cost me about $200 with me doing remove and install. They did a good job.

It'sNotWorthComplaining! · 28th February 2011, 11:28 AM

Originally Posted by Mr Whippy

I can also add half a can. I had a quote of $150 if I removed it. If you have it removed why would you bother trying to glue it when it can be done properly for 150 bucks?

Dave.

Yeah that's telling him!

Don't be a cheap skate

**Jock The Rock** · 12th May 2011, 08:14 PM

To those who have removed the head linings themselves

How did you remove the plastic covers on the up right pillars? They feel as though they are about to break. Which way do I need to 'pull' them for the clips to let go without breaking?

**Gary S11** · 12th May 2011, 08:25 PM

If you go to this link
LROCWA Forum

http://www.lrocwa.org.au/forum/cgi-b...num=1299928669

on the LROCWA sit you can see how i did mine and the description is the link before it
Real easy ..Gary

**OffTrack** · 12th May 2011, 09:00 PM

I've been trying to source a near factory replacement to the original and based on posts to various forums I think I've got reasonably close to an answer.

Allegedly a fabric colour called 2144 Shale is a very close match to the original fabric, and is available in a 1/8" foam backing and 64" (150cm-ish) width which allows the D2 headlining to be covered without joins. This runs to about $30-35 per metre with approximately 2.5-2.75M is required to do the D2 hood lining. I have a swatch of a slightly darker fabric (2075XW Light Graphite) which I'll compare with the factory fabric on the weekend.

If you can be bothered DIY'ing it should cost you under $100 to replace with reasonably original looking head-lining.

SCTextiles distributes this fabric in Australia but has a minimum order of 10m. Judging by a quote I got it's cheaper buying from a trimmer that has stock of the fabric than buying direct.

cheers
Paul

Thread: Disco headlining

Thread Tools

Bookmarks

Bookmarks

Posting Permissions