Disabling Defender immobiliser With Nanocom. and genral immoblizer help

**Benny_IIA** · 20th April 2011, 10:12 PM

Hi all,

My Dog though it would be idea to chew my Defender Key and remote,

The defender was locked with the remote when i last used it. So the red light in the speedo is on, which i guess is the immobiliser.

Also when i put the key in (no remote) and turn the key to position II there is a red light the shape of engine with a lighting bolt through it, on the dash.

So I have a nano com and i had a look around the alarm section with no luck, ( probably changed all the settings while i was at it)

I believe there is a way of Disabling Defender immobiliser With Nanocom is this true? and how is it done?

Thanks Regards Ben...

**Xtreme** · 20th April 2011, 10:49 PM

A slightly different cause but both outcomes seem to have ended up needing the immobiliser to be disabled.

Read posts 255 to 260 in the group buy thread http://www.aulro.com/afvb/electronic...n-news-26.html

That plus the attached spreadsheet should give you an idea of where to reset your immobiliser.

**Benny_IIA** · 20th April 2011, 11:00 PM

Originally Posted by Xtreme

A slightly different cause but both outcomes seem to have ended up needing the immobiliser to be disabled.

Read posts 255 to 260 in the group buy thread http://www.aulro.com/afvb/electronic...n-news-26.html

That plus the attached spreadsheet should give you an idea of where to reset your immobiliser.

Cheers mate..

I will give it ago tomorrow, everyone at my house and people who live next door are getting sick of my defender alarm going off late at night

**Xtreme** · 21st April 2011, 11:57 AM

Let us know how you go - the results may be useful in compiling a future Nanocom Operations Manual or maybe just a section in 'The Good Oil' regarding Nanocom use.

**Benny_IIA** · 21st April 2011, 01:25 PM

Originally Posted by Xtreme

Let us know how you go - the results may be useful in compiling a future Nanocom Operations Manual or maybe just a section in 'The Good Oil' regarding Nanocom use.

I Put in your settings and it now alive

thank you very much.

Much more helpful then the ******* at Austral (my local stealer) and Cairns LR(where it was sold new) they could not even give me the EKA code to drive to austral to get a new fob programmed.

**Xtreme** · 21st April 2011, 05:02 PM

Originally Posted by Benny_IIA

I Put in your settings and it now alive

thank you very much.

Much more helpful then the ******* at Austral (my local stealer) and Cairns LR(where it was sold new) they could not even give me the EKA code to drive to austral to get a new fob programmed.

That's just part of what this forum is all about ............ sharing experiences and helping each other out in a timely manner, where possible.

Now you can have an anxious free and happy Easter.

**Benny_IIA** · 22nd April 2011, 01:07 AM

Originally Posted by Xtreme

That's just part of what this forum is all about ............ sharing experiences and helping each other out in a timely manner, where possible.

Now you can have an anxious free and happy Easter.

Cheers again for that...

Hope you have great easter as well.

Regards Ben...

Ozmatthes · 3rd May 2017, 10:39 AM

I had the problem with alarm beeping when I tried to lock the car. Turned out all it was one of the screws holding the wire to the door had threaded out and wasn't connecting properly. So just replaced with bigger gauge screw and the neighbours were happy again.

**loanrangie** · 4th May 2017, 10:55 AM

Pity a nanocom wont work on a D1, would like to disable the immobiliser on my 10AS alarm.

Thread: Disabling Defender immobiliser With Nanocom. and genral immoblizer help

Thread Tools

Disabling Defender immobiliser With Nanocom. and genral immoblizer help

Alarm beeping when locking

Bookmarks

Bookmarks

Posting Permissions