Page 4 of 4 FirstFirst ... 234
Results 31 to 36 of 36

Thread: carbs to efi: which manifold?

  1. 2nd July 2014, 02:44 PM #31
    PhilipA
    PhilipA is offline Swaggie Subscriber
    Join Date
    Jan 1970
    Location
    Avoca Beach
    Posts
    14,152
    Total Downloaded
    0
    OK - thanks - so if it dumps fuel on the ignition pulse for that cylinder it is
    clearly too late to be fired at that time so I guess the fuel sits in the intake
    manifold above the inlet valve waiting for the next firing.
    Yes and until recently even sequential injection did this above a couple of thousand revs as the rise time for the injectors is/was slower than the valve opening time.
    This may have changed with the latest piezo injectors and will not be a factor with direct injection so they MAY be sequential at higher revs.

    However AFAIK the main benefit of sequential is emissions not performance.
    Regards Philip A
    Reply With Quote Reply With Quote
  2. 11th July 2014, 07:57 AM #32
    russotouristo
    russotouristo is offline Fossicker
    Join Date
    Jul 2011
    Location
    Moscow
    Posts
    75
    Total Downloaded
    0
    just undid the crank pulley bolt.(started the engine with a socket wrench on the bolt). then i removed the alternator belt. it was tough, but we almost removed the steering pump belt - when moving the pump downwards it stops for some reason. i just loosened couple of bolts on its bracket and saw some fluid (which one? coolant? oil? brake fluid?) dropping from one of the bolts.

    the tensioning pulley of the water pump was the toughest. not only the tightening bolt had a 1/2 socket (here we have mainly metric tools and i will have to wait weeks before get the wrench delivered), but the bolt was tightened from the wrong side - the wrench travel is at most 45 degrees restricted by the pulley itself...
    i am afraid the pulley would be pressed on to the crankshaft...

    Sent from my JY-G4 using AULRO mobile app
    Reply With Quote Reply With Quote
  3. 11th July 2014, 09:17 AM #33
    bee utey's Avatar
    bee utey
    bee utey is offline AT REST
    Join Date
    Apr 2009
    Location
    Crafers West South Australia
    Posts
    11,732
    Total Downloaded
    0
    Quote Originally Posted by russotouristo View Post
    the tensioning pulley of the water pump was the toughest. not only the tightening bolt had a 1/2 socket (here we have mainly metric tools and i will have to wait weeks before get the wrench delivered), but the bolt was tightened from the wrong side - the wrench travel is at most 45 degrees restricted by the pulley itself...
    i am afraid the pulley would be pressed on to the crankshaft...
    You know it's trivially easy to acquire a drive belt 10mm longer than original and this makes the tensioner bolt quite easy to access.
    Reply With Quote Reply With Quote
  4. 11th July 2014, 09:53 PM #34
    russotouristo
    russotouristo is offline Fossicker
    Join Date
    Jul 2011
    Location
    Moscow
    Posts
    75
    Total Downloaded
    0
    got it! nice tip! the same refers to the steering pump belt?
    any tips on tightening these belts? whatsort of lever should it be?
    Sent from my JY-G4 using AULRO mobile app
    Reply With Quote Reply With Quote
  5. 13th July 2014, 07:10 PM #35
    russotouristo
    russotouristo is offline Fossicker
    Join Date
    Jul 2011
    Location
    Moscow
    Posts
    75
    Total Downloaded
    0
    got the right wrench and removed the pulley. how do i remove the oil deflector, which is pressed onto the pulley?

    Sent from my JY-G4 using AULRO mobile app
    Reply With Quote Reply With Quote
  6. 10th September 2014, 07:15 PM #36
    russotouristo
    russotouristo is offline Fossicker
    Join Date
    Jul 2011
    Location
    Moscow
    Posts
    75
    Total Downloaded
    0
    well. heat helped me with that reflector. now couple of questions: what is the needed torque for the pulley and how do i apply it/is it critical? :-) te secondone is when undoing the pulley i noticed some oildrips from i didn't get where - it probably wasn't the crankshaft seal, but could easily be steering pump. could it be that belt tension helped the pump's shaft remain sealed? what are the cosequences of using mulfunctioning pump? thanks!
    Reply With Quote Reply With Quote
Page 4 of 4 FirstFirst ... 234
« Td5 quit, will not restart | rev counter off and charge light coming on - alternator ? »

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules

Search AULRO.com ONLY!
 Search All the Web!