Results 1 to 9 of 9

Thread: Wading Plugs

  1. #1
    Ty Guest

    Wading Plugs

    Just wondering when i am supposed to insert the wading plugs on my Defender Tdi. Do i need to do it on all water crossings or just the more extreme (longer) ones? It seems a bit crazy to be crawling around in the mud before and after every creek crossing. Any help would be great.

  2. #2
    Join Date
    Jan 1970
    Location
    Cessnock NSW
    Posts
    4,990
    Total Downloaded
    0
    Wading plugs are there to stop ingress of any foreign matter i.e. water and mud, if your vehicle is new and I assume it could be, if it were mine I would fit it and forget it, my County 110 (Nov 84 doesn't have one and doesn't have oil leaks in that area either) if you dont intend to do any serious 4x4ing leave it where it is, out and the hole clear, it (the hole) serves 2 purposes it also lets out any oil that may be leaking from your rear main bearing oil seal or as in the early Series L/r's if you parked them downhill they leaked G/box oil into the clutch housing until rover put a reverse spiral on the input shaft to pump any oil that accumulated there back into the G/box.
    PS if you forget to put plug insitu and you cross some deep water it will be OK as long as you dont change gears whilst in the water.

  3. #3
    Join Date
    Jan 1970
    Location
    Invermay Tasmania
    Posts
    1,732
    Total Downloaded
    0
    If you do leave it in and forget just remove the plug from time to time and drain out what eva has accumulated say maybe when you service it!!

    Also depending on what you have as most auto's don't need one its only the manuals ( i think )


    adam

  4. #4
    Hellspawn Guest
    :? I don't know if this has been discussed before but I'm wondering further to installation of wading plugs for water work. I'm fairly well set up, got the engine intake above the windscreen and sealed most of the rest with silicone to stop water entry.

    If you have breathers on various parts of the drivetrain should those be blocked as well with golf tees, bolts or whatever else fits when attempting crossings :?:

    I figured also that if I installed fuel filters to the ends of the breathers(early commodore style with pickup facing down) on hellspawn maybe there would be no ingression of dust. Could the same be expected for water ?

  5. #5
    Join Date
    Jan 1970
    Location
    Invermay Tasmania
    Posts
    1,732
    Total Downloaded
    0
    The best thing to do is extend your breathers I have seen people extend the so they end up in the engine bay behind the engine not a hard job I'm sure


    adam

  6. #6
    Hellspawn Guest
    No it's not a difficult job, long way to bring the back diff pipe though..... just curious whether it was a good idea to plug them similar the bell housing or not. [img]style_emoticons/<#EMO_DIR#>/biggrin.gif[/img]

  7. #7
    Join Date
    Jan 1970
    Location
    Invermay Tasmania
    Posts
    1,732
    Total Downloaded
    0
    I don't think it would be a good idea to bloke them thats why they have breathers on them so you don't blow your seals when they heat up


    adam

  8. #8
    Hellspawn Guest
    Problem solved..... thanks [img]style_emoticons/<#EMO_DIR#>/biggrin.gif[/img]

  9. #9
    Join Date
    Jan 1970
    Location
    Ringwood vic
    Posts
    52
    Total Downloaded
    0
    Also if you block breather or have a valve on them (a ls Landcruisers) they will suck water in thru seals and onto bearings when going thru cooling water. Always extend them and put cheapo fuel filters on the end.
    rear diff can be routed up into side panels.

    Bazzle [img]style_emoticons/<#EMO_DIR#>/laugh.gif[/img]

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!