-
1st July 2006, 05:30 PM
#1
Slipping Handbrake
Over the week I decided to finally change out the handbrake for a Rangie job. The drum looked oily with a small amount of seepage showing. I took it off and found the following. A small trace of oil from the hub spiggot coming from higher up on the left hand side. None from the centre. The felt seal was dry. The brake linings were oily.
The oil looked like the original transfer box oil, light brown in colour. Strange, because I had changed to fully synthetic Castrol Syntrax 30K ago. That oil has a red colour to it. Could it be something else? or just some old oil that was trapped in a crevice? 
Trev.
-
1st July 2006, 08:39 PM
#2
so...have you had oil leak onto the brake before.....?
and is everything dry around the brake...?
or do you have oil leaks around there.....?
if you have oil leaks...you will need to degrease it all and drive it to determine
where the leak is exactly.......
as for the brake shoes...normally they should be replaced....but since its only the handbrake.....
try to clean as much of the oil off as you can using plenty of brake cleaner.....
maybe even heat them up in the oven to try and get the oil from in the lining.....it acts like a sponge......
(best done when the missus is out shopping.....)
but the brake cleaner should be good enough.....then clean the shoes with a bit of emery cloth.....
and dont forget to clean the oil off the drum as well.....
there really isnt any crevices that would trap oil unless you went pouring oil over everything....
-
1st July 2006, 08:55 PM
#3
There is some oil (heavy film), on the outside of the drum assembly from the front side. I did not think that it could get in, but maybe thats where the problem lies. I have cleaned off the linings and given them a light sanding, also inside the brake drum. The outer drum and transfer case will get degreased tomorrow so I can attempt to track the leak.
Trev.
-
1st July 2006, 09:03 PM
#4
that would be the only way to attack the problem.....
and the brake should be working again now.....
good luck with it tomorrow....
-
2nd July 2006, 11:14 AM
#5
what can be done to resurrect oil soaked linings or pads is a good soak in a solvent like brake cleaner, although I have used petrol, then remove and either set them on fire or use a blow lamp to boil the residue out. Works fine although I will add the caveat
DO NOT DO THIS AT HOME. THIS IS AN FYI ONLY. THE WRITER IS NOT RESPONSIBLE FOR ANYTHING YOU MAY UNDERTAKE ON YOUR OWN VEHICLE. ANYTHING YOU DO TO YOUR OWN VEHICLE IS AT YOUR OWN RISK.
-
2nd July 2006, 03:15 PM
#6
Thanks Rick. Once I have resolved the mystery of the oil I shall get a new set. keeping the brake linings and setting the car alight is not what I had in mind. 

Trev.
-
2nd July 2006, 05:55 PM
#7
oops, did I neglect to mention that you remove the linings from the vehicle first before, um, cleaning them.
Sorry Trev.
-
2nd July 2006, 07:44 PM
#8
fact is.....once the oil gets into the linings.....you will never get it out.....
setting them on fire and solvents and sanding etc..........
will only clean the surface layer.......when they get hot....oil will work its way to the surface.....
the only cure is replacement.......
but since its only the handbrake.......its not as bad as if it were the main brakes.......
but the above described procedure is used occaisonally but without 100% success.....
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules
Search AULRO.com ONLY!
|
Search All the Web!
|
Bookmarks