Consequence of wheel Size?

Printable View

Show 40 post(s) from this thread on one page

28th July 2007, 04:14 PM
Dauntless

Quote:

Originally Posted by ladas

and I am now looking around for some 235/60/ 16's

235/60-16 is only a 27" tall tyre!

http://www.miata.net/garage/tirecalc.html
28th July 2007, 04:33 PM
GEK064

Well the seller informs me that the mags 31x10.5 R15LT 6 ply rating Kumho Venture A/T are currently on a 84 ranger rover.....will they fit a 99 disco given the caliper and stud pattern?
28th July 2007, 04:47 PM
Slunnie

No. They're a different stud pattern
28th July 2007, 05:15 PM
ladas

Quote:

Originally Posted by Dauntless

235/60-16 is only a 27" tall tyre!

http://www.miata.net/garage/tirecalc.html

Yes exactly, then I can get a 27" - but with an aggresive tread pattern
28th July 2007, 05:47 PM
GEK064

Quote:

Originally Posted by Slunnie

No. They're a different stud pattern

Thanks to all, you've saved me spending money! Well somebody else will need to get that good deal on Ebay.
29th July 2007, 04:14 PM
953

Quote:

Originally Posted by ladas

Yes exactly, then I can get a 27" - but with an aggresive tread pattern

Ladas, Im not quite with u on this 1.U get a more aggresive tread pattern but effectively r lowering your car which would negate theoff road ability of you`re car?????????
Cheers Dean.
29th July 2007, 04:35 PM
ladas

Quote:

Originally Posted by 953

Ladas, Im not quite with u on this 1.U get a more aggresive tread pattern but effectively r lowering your car which would negate theoff road ability of you`re car?????????
Cheers Dean.

Well as I understand it - and I may well be wrong - tyres are not my bag - but the measurement of a tyre is to the wall - surface - bit that is there after the tread is gone..........

The large nobbly tyres - with say 12 mm of tread - would add 24mm (about an Inch) to the rolling dia -

I (especially after the last trip to Tolangy) don't do hard - off road stuff, just stick to the basics. ...........and I have been in positions where I only need a bit of traction - not too bothered with clearance
29th July 2007, 05:11 PM
Utemad

Quote:

Originally Posted by ladas

Well as I understand it - and I may well be wrong - tyres are not my bag - but the measurement of a tyre is to the wall - surface - bit that is there after the tread is gone..........

The large nobbly tyres - with say 12 mm of tread - would add 24mm (about an Inch) to the rolling dia -

I have yet to buy a tyre that measures the same as the dimensions on the sidewall. They have always been smaller. That is overall diameter including tread. So they would be even smaller again measuring without the tread.
30th July 2007, 08:49 AM
ladas

Quote:

Originally Posted by Utemad

I have yet to buy a tyre that measures the same as the dimensions on the sidewall. They have always been smaller. That is overall diameter including tread. So they would be even smaller again measuring without the tread.

Looks like I had better do some homework then, thanks;)
30th July 2007, 11:28 AM
isuzurover

Quote:

Originally Posted by Utemad

I have yet to buy a tyre that measures the same as the dimensions on the sidewall. They have always been smaller. That is overall diameter including tread. So they would be even smaller again measuring without the tread.

As above - tyre dimensions are INCLUDING TREAD.

Tyre dimensions are a funny thing - it is better to go by the tyre and wheel standards manual than what the sidewall says.

Most tyres are smaller in diameter than specified on the sidewall, except for the british tyre sizes. E.g. a 7.50x16 is usually 32", a 9.00x16 is usually 35-36" diameter.

Show 40 post(s) from this thread on one page