Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24

Thread: A bit of advise please

  1. #11
    Join Date
    Oct 2007
    Location
    Perth
    Posts
    330
    Total Downloaded
    0
    Thanks for the replies everyone, I know what you mean Philip everything points to the engine being fine theres no tapping noises on startup, no misses and the economy is good, the only thing that worries me is the black smoke and loss of power.

    I might do a compression test first, that seems the cheapest place to start, no I haven't checked the PCV system. I've got no history on the car so I can only assume its not been done since its come out of the factory...

    Idling is fine, but sometimes when I come off the freeway and sit at the traffic lights the engine idles at 1,500rpm, and then drops to 800 after a few seconds.

    How do I check the temp sender to the ECU ? I'm guessing its the same sender that the temp gauge on the dash uses ? If so then its reading normal temp.

  2. #12
    Join Date
    May 2003
    Location
    On The Road
    Posts
    30,031
    Total Downloaded
    0
    if it was running at all rich,, you wouldnt be getting 14's. plug chop sounds the go---
    "How long since you've visited The Good Oil?"

    '93 V8 Rossi
    '97 to '07. sold.
    '01 V8 D2
    '06 to 10. written off.
    '03 4.6 V8 HSE D2a with Tornado ECM
    '10 to '21
    '16.5 RRS SDV8
    '21 to Infinity and Beyond!


    1988 Isuzu Bus. V10 15L NA Diesel
    Home is where you park it..

    [IMG][/IMG]

  3. #13
    Join Date
    Jan 1970
    Location
    3960
    Posts
    1,161
    Total Downloaded
    0
    G`day Duncan

    Check your fuel pressure regulator .

    There is a vacuum pipe going to it , remove this and any sign or form of fuel on the hose side says it needs replacing .

    It lowers the pressure for slower running and increases for faster running .

    With your economy it has to be something that alters with revs .

    Cheers
    Last edited by PLR; 7th February 2008 at 02:10 PM. Reason: Chabge of to or

  4. #14
    Davo is offline ChatterBox Silver Subscriber
    Join Date
    May 2007
    Location
    WA
    Posts
    2,595
    Total Downloaded
    0
    Yeah, check the easy things first. I was thinking maybe a vacuum leak? It's easy for any vacuum hose to spring a leak, so be sure to check them and of course all connections, fittings, etc.

  5. #15
    Join Date
    Jul 2006
    Location
    Brisbane, Inner East.
    Posts
    11,178
    Total Downloaded
    0
    Does this jigger have an EGO sensor, and, if so, is it faulty?
    URSUSMAJOR

  6. #16
    Join Date
    Jan 1970
    Location
    Avoca Beach
    Posts
    14,152
    Total Downloaded
    0
    1 The temp sender for the ECU is not the same as for the gauge. The gauge one is a single wire sitting next to the thermostat housing, the ECU is on top of the manifold at the front RH, and has 2 wires and an injector plug on it. It should read about 300Ohms at normal operating temp.

    2 No EGO sensor

    3 look I say again , I think it is fine. The soot you see may be water condensing on a cold exhaust.
    Regards Philip A

  7. #17
    Join Date
    Feb 2008
    Location
    Northern Windowlickersville WA
    Posts
    3,403
    Total Downloaded
    0
    As you are in Perth, drop in to either Jordan Rovertech or Guest and Puddey and get the ECU checked. If you have an injection fault, it will send the ECU into 'limp mode" which will make it run rich. generally the fault can be cleared, but it will depend on what the actual fault is.
    Its also worth while checking the pressure regulator on the fuel rail to see if it has stuck open. The fuel rails have a habit of rusting inside and small bits of junk can clog the regulator in an open, or possibly in this case, a closed position increasing the injector pressure. Normal injection pressure should be about 36 psi. Any higher and you are pushing a lot more fuel thru the nozzles.
    Thermostat stuck open or the lack of one in the first place is also something to look at!

  8. #18
    p38arover's Avatar
    p38arover is online now Major part of the heart and soul of AULRO.com
    Administrator
    I'm here to help you!
    Gold Subscriber
    Join Date
    Jan 1970
    Location
    Western Sydney
    Posts
    30,707
    Total Downloaded
    1.63 MB
    At 1 litre/5000 km, I'd say that's better than average for a RR V8! I wouldn't complain about that.

    What plugs are you running? Are they too cold?
    Ron B.
    VK2OTC

    2003 L322 Range Rover Vogue 4.4 V8 Auto
    2007 Yamaha XJR1300
    Previous: 1983, 1986 RRC; 1995, 1996 P38A; 1995 Disco1; 1984 V8 County 110; Series IIA



    RIP Bucko - Riding on Forever

  9. #19
    Join Date
    Jan 1970
    Location
    ACT
    Posts
    529
    Total Downloaded
    0
    Quote Originally Posted by PhilipA View Post
    If you are getting 14l per 100Kms on the freeway and using 1 litre of oil per 5000K, to me it seems there is nothing wrong with your engine.

    You don't start her up cold and move her into the driveway before you check the plugs do you?
    If you have no misses or poor starting and the fuel economy is good, stop worrying.
    The plugs are always sooted on one side on any V8. A bit of idling or a cold start will probably spread it. Why not try driving at 100Kmh on the freeway, then turn off immediately and check the plugs.
    Regards Philip A
    I'm curious about the comment that 'plugs are always sooted on one side of any V8' - if they've got equal fuel feed and similar independent extractors, why would this be? One of the reasons I ask is because I've got a tranverse mounted parallel twin motorbike (TRX850) and it always runs richer on one side (and soots the plug) and I've been told that one cylinder runs hotter than the other on this bike - which I can't work out because they've got equal airflow and similar but independent carbs and exhaust. Surely there wouldn't be big differences in the water channels on each side of the block? Anyway, fortunately on a motorbike with carbs this is easily accounted for by adjusting the jets/needles on each carby independently until neither runs rich.

  10. #20
    Join Date
    Jan 1970
    Location
    Adelaide - Torrens Park
    Posts
    7,291
    Total Downloaded
    0
    I have done tuneups on V8 ski boats in the past where I fitted different heat range plugs to each bank to cure fouling issues. Raw water cooling with no thermostat means each bank runs at considerably different temeratures.

Page 2 of 3 FirstFirst 123 LastLast

Bookmarks

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  
Search AULRO.com ONLY!
Search All the Web!