Reply With Quoteyeppa got that, its the pre 86 one, withh no amp meterOriginally Posted by incisor
SysAdmin (Owner)
this may help, maybe
electrical diagram from Au supplement
2007 Discovery 3 SE7 TDV6 2.7
2012 SZ Territory TX 2.7 TDCi
"Make the lie big, make it simple, keep saying it, and eventually they will believe it." -- a warning from Adolf Hitler
"If you don't have a sense of humour, you probably don't have any sense at all!" -- a wise observation by someone else
'If everyone colludes in believing that war is the norm, nobody will recognize the imperative of peace." -- Anne Deveson
“What you leave behind is not what is engraved in stone monuments, but what is woven into the lives of others.” - Pericles
"We can ignore reality, but we cannot ignore the consequences of ignoring reality.” – Ayn Rand
"The happiness of your life depends upon the quality of your thoughts." Marcus Aurelius
AULRO Holiday Reward Points Winner!
yeppa got that, its the pre 86 one, withh no amp meter
AULRO Holiday Reward Points Winner!
one poic is what i was trying toi sort out. second pic is my mock up dash wired up, all i now need to know is where the wires go for the grouped lighting
cheers
Last edited by clean32; 31st July 2010 at 09:43 AM.
Master
I had the dash out of my 1990 Isuzu County just last week as the dash surround had cracked so I replaced it with a new one.
Apart from the 2 big multi-plugs on the back of the warning light cluster only one of the other warning lights was connected to anything - and my car has hardly been messed with since it left the factory.
Just like your photo there were 5 white warning globe holders but only the rear heated window warning light was connected - can't remember the colours but will check for you. If you hold the warning cluster up to a light you'll see that there's no writing on some of the warning lights, they are simply un-used. Another has a seat belt warning signs on it that wasn't used in this market at that time.
I'll pop outside now and check the wiring colours for you.
Jon
AULRO Holiday Reward Points Winner!
The other ones are, brake emergency this is connected to the balance thing on the brake lines just under the booster, left top light.
Park brake bottom right
middle is green light that’s connected to the immobilizer( but unlike a puma a 10mm spanner can fix that)
Top right rear demister
So im all sorted now
All I have left to do is fined the wiring diagram for the Tacho ( that’s with my original mud map)
Master
OK, just been outside and got the dash out for you:
.
.
.
.
.
.
.
.
.
.
.
Just kidding... that was last week!
OK, so I just popped out the warning cluster again and I only had 4 white globe holders as one was missing. As per my earlier post only one of them is used though. It's for the heated rear window warning lamp at the top right and the wires are white/green and black:
The 4 other globe holders at top left, bottom left, bottom middle and bottom right aren't used in my car, the pic below shows why as top left is "Park Brake" - my car uses the (P) light when the handbrake is applied, bottom left is blank, bottom middle is blank and bottom right is "24V", so also not used.
Hope this helps,
Jon
Master
Our posts just about crossed. So it sounds like your light cluster is different to mine as Park Brake and Brake emergency are in different spots.
Jon
AULRO Holiday Reward Points Winner!
yeppa
the number of difrent wiring diagrams i have seen, all just difrent enough to get you realy confused
TopicToaster
Cleaner, I have to pull mine out soon, trip meter isn't reading.
Is yours similar to this:
?
AULRO Holiday Reward Points Winner!
mate, if you are just looking at your trip meter than you have no problems with wiring. the speedo is held in with 2 brackets, there may be an earth on one of these and the 2 lights which just pull out. i doint think you can pull your speedo apart though?
Posting Permissions
| Search AULRO.com ONLY! |
Search All the Web! |
|---|
|
|
|
Bookmarks