Puma Alarm System Advice Needed

**dmdigital** · 4th January 2011, 11:39 PM

Are you sure?
The volumetric sensor comes off the 10AS unit (sensor input and power supply), not the ECM. The volumetric sensor will trigger the alarm which will then trigger the immobiliser was my understanding. Same as door and bonnet switches.

From the wiring diagrams the harness may still be there. 3 wires terminating behind headlining above RH B-Piller, White/Black, Brown, Black. Haven't checked mine.

**solmanic** · 5th January 2011, 10:01 AM

Originally Posted by davep130

...I spoke to the dealer today they didn't think there was an interior sensor but weren't sure and they were some what surprised when I showed them the manual which states that there is.

The dealer is going to contact Land Rover Australia to get some technical advice.

Why on earth is it that dealers know so little about the Defender? The Defender manual has had info on the interior motion sensor in it since I had my last 02MY one but they are not fitted to Australian spec models as others have pointed out. How is it that the dealer is surprised to learn this? Do they never even read these things or was he only hired last Thursday?

**5teve** · 5th January 2011, 03:31 PM

I have a 2002 td5 defender and the wiring is all there ready to be connected to the alarm system... its on my long list of things to pick up for the car... its a simple plug in job, however how it fits i do not know.. i guess just fixed into the plastic or the headlining...

Anyone have a part code for it?

Steve

miky · 5th January 2011, 09:12 PM

And I have been boasting to admirers (of the car) that my 110 had motion sensors fitted. That's what it says in the manual

Perhaps we don't get a separate manual for Australia?

.

**Naks** · 5th January 2011, 09:33 PM

Originally Posted by miky

Perhaps we don't get a separate manual for Australia?.

You don't, all English-speaking countries get the same manual

**LRO53** · 6th January 2011, 09:12 AM

Australian Spec miss's out on.

That Sensor for alarm
XS, County Spec Trim Levels (Heated Seats, Screen etc etc)
rear seats if 03-05 td5 90 aus spec

Possibly a few other things i cannot think of right now.

**sashadidi** · 7th January 2011, 04:32 AM

Originally Posted by 5teve

I have a 2002 td5 defender and the wiring is all there ready to be connected to the alarm system... its on my long list of things to pick up for the car... its a simple plug in job, however how it fits i do not know.. i guess just fixed into the plastic or the headlining...

Anyone have a part code for it?

Steve

either; labeled as Alarm sensor ?
YWC102900LNF Vin (v0ta977525 to (v)5a701968
or YWC500470 (v)5a701969

**Zinke** · 9th January 2011, 10:24 AM

Connector for the wiring loom for the sensor and the interior lights is behind the headlining near the front right A pillar. Its not always a plug and play job, firstly im not sure if both alarm ECU's support it though if you have central locking it defiantly will work. Sometimes it needs enabling with a Nanocom or such like too.

Pete.

**davep130** · 10th January 2011, 09:44 PM

Thanks All for your feedback.

Dealer advised after inspection today that the sensor is not fitted in the vehicle. They acknowledged that the manual was misleading.

I will investigate the wiring and sourcing a D1 sensor and will have a go at installing, will post the results.

Cheers

Dave

**dmdigital** · 11th January 2011, 06:07 AM

Originally Posted by Zinke

Sometimes it needs enabling with a Nanocom or such like too.

Nanocom doesn't yet work on the Puma.

Thread: Puma Alarm System Advice Needed

Thread Tools

Bookmarks

Bookmarks

Posting Permissions